縱向焊縫 的英文怎麼說

中文拼音 [zōngxiànghànféng]
縱向焊縫 英文
longitudinal seam
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 縱向 : [造紙] direction; machine direction; endwise; longitudinal direction; vertical; longitudinal縱向...
  1. This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.

    研究表明裂紋是從縱向加勁助未熔透的對接焊縫中起始的。
  2. In addition to, the fatigue crack between web and upper flange of welded steel crane beam on heavy duty service was discussed, and based on long - term observation and research, the author classified fatigue crack into bearing type and middle type crack along the horizontal direction. the causation, distributive law and mechanism of the crack were analyzed, and the precautions to take and the measures to remedy crack were presented. the main defacts including damage, crack, erosion and aging in structures, especially in concrete structure were introduced ; the defact mechanism was analyzed and the precautions to take were also given

    另外，作者對重級工作制焊接鋼吊車梁腹板與上翼緣連接焊縫的縱向水平疲勞裂縫進行了長期的觀察和研究，根據疲勞裂縫產生的不同機理，將其分為支點裂縫和肋間裂縫，並討論了兩類裂縫產生的原因、分佈規律、機理以及防治的措施；對工程中經常遇到的結構構件，尤其混凝土構件的幾種主要病害（損傷、裂縫、腐蝕與老化）進行了機理分析並提出了防治措施。
  3. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  4. Vertical welds not completely removed by backgouging shall be performed vertically up, unless specifically approved in writing by secco

    對于不能通過逆向刨削完全清除的縱向焊縫應垂直施焊，除非賽科公司有特殊的書面指示不用垂直施焊。
  5. Longitudinal and circumferential weld seams are pl inspected for class 150 #, for other classes will be inspected with x - rays and / or us

    過濾器之縱向和周圍焊接縫是染色探傷檢查，其它將以x -射線和/或超音波檢查。
  6. Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced

    焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。
  7. Non - destructive testing of steel tubes - automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections

    鋼管的無損試驗.縱向缺陷探測用電焊鋼管焊縫的自動超聲波檢驗
  8. Pipes and fittings of longitudinally welded hot - dip galvanized steel pipes with spigot and socket for waste water systems - part 2 : dimensions ; german version en 1123 - 2 : 1999

    帶插接套管廢水管道.縱向焊縫熱鍍鋅鋼管道和管件.第2
  9. Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - part 3 : system x ; dimensions ; german version en 1124 - 3 : 1999

    帶插接套管廢水管道.縱向焊縫不銹鋼製造管和管件.第3
  10. Pipes and fittings of longitudinally welded stainless steel pipes, with spigot and socket for waste water systems - part 2 : systeme s ; dimensions ; german version en 1124 - 2 : 1999

    帶插接套管廢水管道.縱向焊縫不銹鋼製造管和管件.第2
  11. Steel tubes. seamless or longitudinally welded stainless steel tubes for exchangers in aircraft construction. dimensions. technical delivery conditions

    鋼管.飛機結構交換器用無縫或縱向焊接不銹鋼管.尺寸.技術交貨條件
  12. Standard specification for steel line pipe, black, plain end, longitudinal and helical seam, double submerged - arc welded

    雙埋弧焊縱向和螺旋焊縫平頭無鍍層鋼制總管的標準規范
  13. Petroleum and natural gas industries. non - destructive testing methods of steel tubers for pressure purposes. ultrasonic testing of the weld seam of elcctric resistance and induction welded steel tubes for the detection of longitudinal imperfections

    石油天然氣工業.承壓鋼管無損檢測方法.電阻焊和感應焊鋼管焊縫縱向缺欠的超聲波檢測
  14. Petroleum and natural gas industries. non - destructive testing methods of steel tubers for pressure purposes. ultrasonic testing of the weld seam submerged arc - welded steel tubes for the detection of longitudinal and or transverse imperfections

    石油天然氣工業.承壓鋼管無損檢測方法.埋弧焊鋼管焊縫縱向和或橫向缺欠的超聲波檢測
  15. Longitudinal contraction deformation ： the component contracts in the weld direction after weiding

    縱向收縮變形：構件焊后在焊縫方向上發生的收縮。
  16. Non - destructive testing of steel tubes - automatic full peripheral ultrasonic testing of seamless and welded except submerged arc welded tubes for the detection of longitudinal imperfections

    鋼管的無損檢驗.縱向缺陷探測用無縫焊接鋼管
  17. Non - destructive testing of steel tubes - part 8 : automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections

    鋼管的無損檢驗.第8部分:檢測縱向缺陷用電焊鋼管焊縫的自動超聲試驗
  18. Non - destructive testing of steel tubes - part 5 : automatic full peripheral magnetic transducer flux leakage testing of seamless and welded except submerged arc welded ferromagnetic steel tubes for the detection of longitudinal imperfections

    鋼管的無損檢驗.第5部分:檢測縱向缺陷用無縫和焊接
分享友人
分享到 Line

分享到臉書