總縱彎曲 的英文怎麼說

中文拼音 [zǒngzōngwānqū]
總縱彎曲 英文
the total longitudinal bend
  • 總 : Ⅰ動詞（總括; 匯集） assemble; gather; put together; sum up Ⅱ形容詞1 （全部的; 全面的） general; o...
  • 縱 : Ⅰ動詞1 （釋放; 放走） release; set free; let go 2 （放任; 不約束） indulge; give oneself up to; l...
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. The plating in ships is generally subjected to combined in - plane and lateral pressure loads. in - plane loads include biaxial compression / tension and in - plane bending and edge shear, which are mainly induced by overall hull girder bending and / or torsion of the vessel. lateral pressure loads are due to water pressure and cargo

    面內載荷分為軸向壓應力或拉應力、邊緣剪切應力以及面內軸向彎曲應力。實際的船舶結構中面內載荷通常由船體梁的總縱彎曲或者船體梁的扭轉引起。側向壓應力則由水壓力和貨物壓力引起。
  2. The influence of such parameters as axial load index, aspect ratio and percentages of lateral reinforcement, on seismic performance of reinforced concrete frame column in hong kong and analyses the distribution relationships of flexural deformation, shear deformation and slippage of longitudinal reinforcement in joint zone

    根據試驗結果，討論了軸壓比、配箍率、剪跨比等參數對其抗震性能的影響，分析了水平荷載作用時塑性鉸區的彎曲變形、剪切變形和縱向鋼筋粘結滑移變形所產生的位移在框架柱總水平側移中所佔的比例及其變化規律。
  3. Test method for overall longitudinal bending of glass fiber reinforced plastics fishing vessel

    玻璃鋼漁船總縱彎曲試驗方法
  4. In the analysis of the elastic local buckling strength of the plates in stiffened plates, an analytical expression is derived for calculating the local strength of a stiffened plate subjected to biaxial thrust considering plate / stiffener interaction and welding residual stresses and initial deflection

    由於船體中的加筋板結構的受力情況是十分復雜的，除了主要受到由於總縱彎曲而產生的縱向壓力以外，還會受到橫向的壓力以及垂向壓力。
  5. In this paper, 3 - d fem for the global ship, by adding loads and inertia adjustment, is used to calculate its longitudinal strength, longitudinal bending distortion and stress distribution, and the efficiency pf the superstructure to stand against longitudinal strength, which present a foundation for the check of ship ' s longitudinal strength

    本文採用整船三維有限元分析方法，通過整船加載和慣性平衡處理，計算出設計目標船的總縱彎曲變形和應力分佈，以及上層建築參與船體總縱強度的有效度，為船體總強度校核提供依據。
  6. Then, a step - by - step increase of vertical bending curvature is applied to the hull girder assuming that the plane cross section remains plane. at each incremental step, the stress of the cross section is evaluated using the average stress - strain curves of the elements as well as the incremental bending moment due to the curvature increment

    船體總縱極限彎矩的計算，由於要計及材料的和幾何的非線性因素而變得十分復雜，必須用增量的方法逐步計算，獲得完整的彎矩?曲率曲線后，才能得到總縱極限彎矩值。
  7. Then, a step - by - step increase of vertical curvature is applied to the hull girder assuming that the plane cross section remains plane. at each incremental step, the stress of the cross section is evaluated using the average stress - strain curves of the elements as well as the incremental bending moment due to the curvature increment. performing sample calculations on existing girder models tests under pure bending, the rationality of the proposed method was examined

    假設船體橫向框架材足夠強，因而板架的整體破壞不會發生；基於梁?柱理論、理想彈塑性假設、平面假設，建立了拉伸和壓縮加筋板單元的平均應力?應變關系曲線，應用船體結構總縱極限強度的簡化逐步破壞分析方法計算船體總縱極限彎矩，並據此開發了計算程序sus 。
分享友人
分享到 Line

分享到臉書