繪圖限制 的英文怎麼說

中文拼音 [huìtúxiànzhì]
繪圖限制 英文
drawing limits
  • 繪 : 動詞（畫出圖形; 描寫） paint; draw
  • 圖 : Ⅰ名詞1 （繪畫表現出的形象; 圖畫） picture; chart; drawing; map 2 （計劃） plan; scheme; attempt 3...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 繪圖 : plot; draw; sketch; plotting; mapping繪圖板 drawing board; field plotter; plotting board; plottin...
  • 限制 : place [impose] restrictions on [to]; astrict; restrict; limit; confine; shut down on [upon]: 限制...
  1. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  2. Status chart will be drawn based on task, duration and status of the project

    根據任務，期限，項目狀態來繪制狀態圖。
  3. The results of the experiment are in good agreement with the data of theoretical calculation and the actual conditions of earthquake calamity. these data and information give a convenience for the following work. the finite element analysis ( fea ) has been completed within the environment of ansys

    有限元分析主要以ansys為工具對煙囪進行了動應力計算，得出了在不同地震波水平和豎向激勵下動應力隨高度分佈情況，並據此繪制了動應力隨高度變化曲線圖。
  4. The paper mentions the design of three - dimensional graphics modeling in the mine such as shaft, laneway, and equipment of transport and mining. human - computer interaction and viewpoint rambling in the demo system are realized so that the simulating staff may look at circumstances from different viewpoint and positions. under the precondition of limited resources holding, the contradiction between the fidelity of image display and real - time feature of system interaction process is better resolved with using of display list and model culling technology

    論文中採用了opengl圖形庫的基本繪圖函數進行三維圖形的模型設計，並詳細給出了立井、拱形巷道、梯形巷道以及工作面支架和井底運輸巷道設備的三維圖形設計方法；並著重分析人機交互與視點漫遊功能的技術在系統中的實現；在佔用有限資源的前提下，為了提高場景實時顯示速度，論文中採用顯示列表和模型淘汰等技術，並編制出了一個虛擬礦井實例。
  5. This system is based on the limit design method of bearing, emphasize on analyzing, calculating and choosing tolerance of bearing parameter, and as well introduces design and actualizing method of automatic drawing

    系統以「軸承極限負荷設計法」作為設計基礎，著重探討軸承參數的分析計算及公差選取，並簡要介紹了圖形自動繪制及處理的設計與實現方法。
  6. By this program, finite element mesh automatic dissection, finite element calculation, optimum design of structures, finite element mesh drawing, displace of finite element mesh drawing are integrated, which makes structural analysis easier

    通過這套程序，實現了有限元網格自動剖分，有限元計算，結構優化設計，有限元網格圖繪制，有限元網格變形圖繪制的一體化，使得計算成果的分析工作簡潔、方便。
  7. Picture including any subjects or components depicted thereon submitted to the client cannot be copied, reproduced, posted, published, uploaded, transmitted or distributed or resold or offered free of charge or with monies to any person or organisation in digital, slide, print or any other format by any means electronic, mechanical, micro - copying, recording, storage retrieval system or otherwise or media unless otherwise agreed in writing on the suppliers form

    客戶獲提供的圖片包括其描繪的任何題材或組成部份，不得採用任何方法電子機械縮微復印錄制存取系統或其他方法或媒體，以數碼幻燈片印本或任何其他格式復印復制張貼刊印上載傳輸分發轉售或提供不論免費或收費提供予任何人士或組織，除非供應機構的表格上另行書面同意者，則不在此限。
  8. 3. set up grading estimating criterion of gas source rocks with the gas hydrocarbon expelling intension. figure out the corresponding organic carbon content threshold value, and plot grading estimating plates of oil and gas carbonate source rocks in tarim basin

    基於排氣強度的大小確定了氣源巖分級評價標準，並計算了相應的有機質豐度界限值，繪制了塔里木盆地碳酸鹽巖氣源巖有機質豐度分級評價圖版。
  9. Clipping is restricting drawing to a certain region

    剪輯是將繪圖限制在某個區域。
  10. Recurring to pre - process program of ansys and drawing functions of winsurf, pre - process program serving to finite elements auto - division of dam bodies and basements models and post - process program capable of plotting various isolines of stress and dams " distortion are worked out. collecting program of data files necessary for dams " dynamic stability analysis is also finished

    藉助于ansys前處理程序和winsurf繪圖功能，用vb6 . 0語言編制了用於進行壩體?壩基模型有限元網格自動劃分的前處理程序和能夠繪制各種應力等值線或壩體變形圖的后處理程序；編制了進行土石壩地震穩定性分析所需要的數據文件集成程序。
  11. In order to analyse the stability of the slop of this area, the longmen apex was chosen as a typical slope

    為分析長白山天池地區斜坡穩定性，選取龍門峰作為典型斜坡，採用有限元法對其進行應力、位移模擬分析，繪制最大、最小主應力等值線圖。
  12. On the theory analysis, the post insulator structure is divided to triangle cell and electric field distribution including cleanness and covered with snow or ice etc is calculated by finite element method using fortran language. then the results are analyzed and the point of max electric strength was found

    在理論分析方面，採用有限元方法對支柱絕緣子進行三角單元剖分，應用並修改fortran語言做電場計算程序，計算了無冰雪、冠雪、覆冰等三種情況下的電場分佈，繪制了等位線圖。
  13. 374 - nt sequence analysis between nt 47 - 420 and restriction enzyme ( re ) clevage site mapping of f gene between nt 34 - 1682 were used to compare the 18 isolates for genetic analysis. a phylogenic tree was constructed based on the 374 - nt - sequence data of eighteen isolates in the study and 37 ndv reference strains from genbank and published resources

    通過dnastar軟體對f基因47 470nt間片段進行同源性分析比較並繪制了遺傳進化樹枝狀結構發生圖，結合334 1672nt間三種限制性內切酶（ re ： hinf ， bsto及rsa ）位點的分佈情況，確定了這些分離株的基因分類地位。
  14. The main contents are as follows : 1. this paper discusses the structure of cad system. according to the design process of the plane gate, this paper combines the structure design, special fem modeling and working drawing and calculation description in pgcad system

    主要研究內容如下： 1 、研究探討了cad的系統結構；根據平面閘門的設計過程和特點，採用集平面結構設計? ?有限元建模? ?施工圖繪制? ?計算說明書生成於一體的設計方法。
  15. To produce lup and lut for the study of broad landuse pattern in the prd region, an innovative hierarchical image processing approach has been adopted to maximise the information extraction from landsat etm images

    為繪制用於珠江三角洲地區土地利用模式研究的土地利用圖和土地利用表，我們採用了創造性的分級圖像處理方法，以便最大限度地從地球資源衛星etm圖像中獲取資訊。
  16. Finally, in order to improve the efficiency of the calculation and design, a software on finite element graphic treatment using vba connecting fortran program and autocad 2000 is developed to make structural analysis easier than before, with which the internal forces figures ( including bending moments, axial forces and shearing forces ) and structural deformation figures are drawn automatically

    4 、為提高設計計算的效率，利用vba開發了相應的有限元圖形處理軟體，該軟體實現了fortran程序與autocad的連接，利用桿系有限元程序計算得到的結果，自動繪制出內力圖（包括彎矩、軸力和剪力）以及結構的變形圖，圖形的自動形成使得計算成果的分析工作簡潔、方便。
  17. The main contents are as follows : l. this paper discusses the structure of cad system. according to the design process of the miter gate, this paper adopts parallel structure to combine the plain structure design, spacial fem calculations and working drawing in rzmcad system

    主要研究內容如下： 1 、研究探討了cad的系統結構；根據人字門的設計過程特點，研究採用了集平面結構設計? ?空間有限元分析? ?施工圖繪制於一體的并行結構設計方法。
  18. Then a dynamic visualization software - - afterdraw, which aims at 2d elastic - plastic fem, is programmed. afterdraw is capable of drawing the deformation figures of material, the regions of plasticity and the regions of tension distributing figures, primary stress vector figures and primary strain vector figures. besides, atterdraw could realistically dynamically simulate the deformation of the whole process of construction

    在此基礎上，研究了針對二維彈塑性有限元的動態可視化后處理軟體afterdraw ， afterdraw能夠繪制基坑工程各步施工的結構變形圖、塑性區和受拉破壞區分布圖、主應力矢量圖和位移矢量圖， afterdraw還能夠逼真地動念模擬基坑工程整個施工過程變形情況。
  19. In chapter 2, a new ir imaging model for city buildings has been established based on meteorology, heat transfer and infrared physics. we first analysis all kinds of main factors affecting the ir characteristic of city buildings, then by using the methods such as multi - layer finite difference the surface temperatures of building and other surrounding objects are acquired. combining the methods of classified modeling and special modeling we constitute the large - scale complex urban ir scene and render the ir images of urban scene at various time

    本文第二章從氣象學、傳熱學和紅外物理學原理出發，分析了影響城市建築物紅外特性的各種主要因素，採用多層有限差分等方法求解建築物及周圍物體的表面溫度，建立了城市建築物紅外成像模型；採用分類建模和特殊建模相結合的方法構建了大規模復雜城市場景的紅外模型，繪制出了不同時刻城市復雜場景紅外成像圖。
  20. The finished 2d small - sized plotting software has good plotting function, which could plot not only basic pictures of line and arc, but also all kinds of curves. both mouse and keyboard are used for interface development. in picture function manipulation, there are many options such as moving, rotating, mirroring, copying, deleting and etc., which are convenient for users to build fem geometric model

    所開發的二維小型繪圖軟體在繪圖功能上比較完善，能完成從直線到圓弧的基本圖形的繪制，也能完成各種曲線的繪制，可生成復雜的幾何圖形；在人機交互上採用了鼠標繪圖和數據輸入繪圖的完整功能；在圖形功能操作上，實現了圖形的拾取、選擇平移、旋轉、鏡像、復制、拷貝、刪除等諸多選項，方便用戶快速建立有限元幾何模型。
分享友人
分享到 Line

分享到臉書