缸蓋螺栓 的英文怎麼說

中文拼音 [gānggěluóshuān]
缸蓋螺栓 英文
cylinder bolt
  • 缸 : 名詞1. （盛東西的器物） jar; jug; vat; crock 2. （缸瓦） earthenware with crude glaze 3. （像缸的器物） jar-like things
  • 蓋 : 蓋名詞（姓氏） a surname
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 栓 : 名詞1. （可開關的機件） bolt; plug 2. （塞子） stopper; cork
  • 螺栓 : bolt; screw bolt; threaded bolt
  1. One machinery makes wen zhoudong limited company is to be engaged in research, development, production, sale is domestic and international the gas a powerful person of all sorts of medium compressor, a powerful person piece, lever of annulus of bedspring, piston, piston, piston, sealing ring, crosshead, crosshead is sold, copper is covered, bolt of connecting rod, connecting rod,

    溫州東一機械製造有限公司是從事研究、開發、生產、銷售國內外各種介質壓縮機的氣閥、閥片、彈簧、活塞、活塞環、活塞桿、密封圈、十字頭、十字頭銷、銅套、連桿、連桿螺栓、軸瓦、曲軸、缸體及缸蓋、缸套、凈化設備及部件、冷卻器等壓縮機配件的專業技術型企業。
  2. Internal combustion engines. cylinder head bolts. specifications

    內燃機.氣缸蓋螺栓.技術條件
  3. Cylinder head fixing stud

    汽缸蓋固定螺栓
  4. Loosely install all the head bolts and the special washers ， then thread them in until they are finger - tight

    鬆鬆地裝上所有的汽缸蓋螺栓和特殊?圈，然後用手鎖緊它們。
  5. The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening

    發動機關鍵工位螺栓包括連桿螺栓、曲軸螺栓、主軸承蓋螺栓、氣缸蓋螺栓、飛輪螺栓和減振器螺栓等均屬螺紋聯接。
  6. Further more, the fracture possibility is analyzed with fracture mechanics after the stress calculation of local high stress area around the bolt hole in shell flange and the measurement of fracture toughness of gray cast iron. the improving structure of bolts connected head and shell flange is brought forward

    此外，在計算獲得缸體法蘭螺栓孔局部高應力區的應力水平后，由斷裂力學分析發生脆性斷裂的可能性，並提出烘缸缸體與缸蓋聯接結構的改進方案。
  7. Chapter six, the two main problems of the subject yc6108zq engine cylinder head - - - - - - the bolt is elongated. monitors the ultra limit phenomenon in the corner, are discussed and analyzed

    第六章針對課題的yc6108zq發動機缸蓋螺栓在裝配及使用中存在的兩個主要問題：螺栓拉長、轉角監測超限，引起的發動機在使用中出現了沖缸墊現象進行了研究。
  8. Tests are carried out on mechanical performance, tired performance, rubing performance and gasket to bear the weight of performance to analyze the existing problems in the assemble technology of bolt production. the improvement measures of this model the cylinder head and the corresponding torsion and checks the standard are put forward in the thesis according to actual product conditions

    對缸蓋螺栓機械性能、疲勞性能、摩擦性能及缸墊承載性能進行了測試，分析了現生產螺栓裝配工藝存在的問題，根據實驗情況及生產條件，提出了該機型缸蓋螺栓裝配工藝改進措施及相應的扭矩檢查規范。
  9. In practical application, the m10 180 bolts, which are installed in the head cover of the torque divider of ts5560 special automobile, sometimes fracture all of a sudden. according to the tests of acceleration, stress and strain, and the exciting test, it is resonance vibration that leads to the compound - bending fatigue fracture of the bolts. the exciting force caused by drive system, transmitted through the torque divider, produces a 1000 - 1500hz cyclical excitation at the junction of the bolts and head cover, which causes the first order bending resonance vibration of the bolts

    通過加速度、應力應變測試實驗和激振試驗的研究，發現ts5560特種車分動器取力器氣缸端蓋m10 180螺栓斷裂問題是由於共振引起的雙向彎曲疲勞斷裂：傳動系統工作所產生的激勵，經過分動器結構的傳遞（特別是分動器一階扭轉模態的放大） ，在螺栓的連接處產生1000 1500hz的振動激勵，其導致螺栓一階彎曲共振，在螺栓一階彎曲模態的阻尼比較小的情況下，使得螺栓產生較大的共振響應，導致螺紋處的彎曲動應力較大，疲勞壽命較低。
  10. The cylinder head is attached to the block with high - tensile steel studs

    氣缸蓋與氣缸體用高強度的鋼螺栓縛連結。
分享友人
分享到 Line

分享到臉書