缺口韌性 的英文怎麼說

中文拼音 [quēkǒurènxìng]
缺口韌性 英文
notch ductibility
  • 缺 : Ⅰ動詞1 （缺乏; 短少） be short of; lack 2 （殘缺） be missing; be incomplete 3 （該到而未到） be ...
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 韌 : 形容詞（不易折斷; 柔軟而結實） pliable but strong; tenacious; tough
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 缺口 : 1. （物體邊緣缺掉一塊） breach; gap; loophole 2. （不足;缺額）insufficiency3. [機械工程]notch
  • 韌性 : 1. （指頑強持久的精神） tenacity 2. [力學] toughness; ductility; ductibility
  1. Nonpolar polypropylene has bad compatibility with mmt even after organic modification to mmt. so polypropylene ( pp ) grafting acrylic acid was produced by the suspension grafting method as compatilizer. as pp / mmt nanocomposites prepared from htab modified mmt as concerned, the interlayer spacing of mmt is 4. 61nm, 4. 2nm and 4. 09nm respectively when the mmt content is 1 %, 2 % and 3 %. so, the abtained nanocomposites has intercalated structure

    當土含量為2 ，相容劑用量為15時力學性能最好，缺口沖擊強度和拉伸強度分別達到16 . 45kj m ~ 2和35 . 77mpa ，分別比純pp增加了280和4 . 3 ，蒙脫土的加入起到了增韌和增強的雙重作用。
  2. The results showed that the notched impact strength of pvc / acr blends was improved remarkably and the tensile strength and the flexural strength of the blends have not obviously changed. the notched impact strength of pvc / acr blends was increased to about 3 times more than the pure pvc when the ratio of pvc / acr is 100 / 6 ( wt )

    結果表明，所合成的acr和pvc共混后能提高pvc的抗沖擊性能，並呈現明顯的韌性斷裂特徵，而材料的拉伸性能和彎曲性能下降不大，當pvc acr = 100 6時，共混體系的缺口沖擊強度較純pvc提高3倍多。
  3. The following results are achieved : ( 1 ) in accordance with the empirical electron theory of solids and molecules, considering the number of covalent bond pairs on the strongest bond in a segregation structure na, the elements for matrix - strengthening can be chosen. ( 2 ) on the basis of the available phase - equilibrium thermodynamics calculation of alloy system and phase diagrams, which have been worked out, the contents of alloy elements can be identified with reference to the types, quantity and phase - transformation of carbides. ( 3 ) both the values relating to toughness ( including bending strength, yield strength, impact value of unnotched samples ) and hardness of new dm9 die steel are higher than those of crl2mov die steel

    結果得出： （ 1 ）根據固體與分子經驗電子理論，利用偏聚結構單元的最強共價鍵上的共用電子對數n _ a ，可以選擇工模具鋼基體相的強化元素； （ 2 ）根據合金系相平衡熱力學計算及已有的相圖，可以碳化物類型、數量及其相變確定合金元素含量； （ 3 ）新型dm9鋼在強韌性（抗彎強度、屈服強度、無缺口沖擊值）和硬度方面均高於cr12mov鋼； （ 4 ）以dm9鋼與6crw2si 、 7cr2wmovsi （ dm7 ） 、 h13和cr12mov四種模具鋼的實驗比較，進一步驗證了上述冷作模具鋼合金設計方案是合適的。
分享友人
分享到 Line

分享到臉書