置零調整 的英文怎麼說

中文拼音 [zhìlíngdiàozhěng]
置零調整 英文
zero set
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 零 : Ⅰ數詞1 （零數） zero2 （數的空位） zero sign （0）; nought 3 （表示沒有數量;無） nil; nought 4 （...
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  2. Remedy : check zero point correction of the star and re - adjust if necessary

    方法：檢查零點位置是否正確，並且需要時，加以調整。
  3. At last, the experiment result proved the effectiveness of the spectrum rebuilding technology. the experiment result show that the wavelength detection accuracy is improved by an order of magnitude using the spectrum rebuilding technology compared with that obtained from direct peak search. some other schemes to enhance the accuracy are illustrated

    最後列舉了其它幾種提高測量精度的方案，包括關鍵器件可調諧濾波器的位置變化提高信噪比，調整探測器pinfet的輸出電壓的零點以提高a / d採集卡的利用率，以及採用系統參考消除系統誤差造成的波長漂移。
  4. When the ballbot ' s goal is to stand still, its control policy tries to simultaneously drive the body ' s position and speed as well as its tilt and tilt rate to zero in each direction, while minimizing the actions needed to do so

    若機器人要站立著不動，它的控制規則會試圖將身體的位置與速度，以及每個方向的傾斜和斜率同時調整到零，並且會盡量減少要維持不倒所需的動作。
  5. The upper slotting / crease shaft is using automatic plane minor adjustment sysem, also allow roational adjustment of 360 degrees whatever operating or stop. the slotting shaft also using zero - storing system

    上刀軸裝設平面式自動微調裝置，刻度清晰，不論運轉或停上均可做360相位調整，刀軸及附自動歸零裝置。
分享友人
分享到 Line

分享到臉書