翹曲線 的英文怎麼說

中文拼音 [qiáoqūxiàn]
翹曲線 英文
warp line
  • 翹 : 翹動詞（一頭向上仰起） stick [hold] up ; bend [turn] upwards; curl up
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  2. Under certain conditions, the calculating formula of interlayer stress and the stress - distributing diagram in cut planes are provided, and the mathematical model for warpage deformation calculation is also established

    建立了翹曲變形的數學模型，討論了各種工藝參數（層數、掃描線長、成型室溫度、層厚等）對翹曲變形量的影響。
  3. Now, it is important to develop the composite blade researching, two measures including analysis methodology and finite methodology are provided. in this text, the finite rotation composite beam theory developed by hodges and his co - workers, during the late 1980 ' s, is adopted in order to research rotor of helicopter. a liner and two - dimension finite analytic measure is used to calculate the section characteristic and strain of the blade ; a semianalysis methodology is used to calculate the sensitive degree of section characteristic

    以giavotto的線性二維有限元分析模型為基礎考慮了復合材料槳葉的結構和變形特點，計入了剖面翹曲的影響，在此基礎上編制了具有八節點等參元復合材料槳葉剖面剛度計算的有限元程序，分析計算了復合材料梁的剖面剛度、彎曲中心、剪切中心；並利用半解析法進行剖面剛度、剪切中心、彎曲中心的參數靈敏度分析。
  4. The device i - v characteristic curves " shangqiao at high temperature while not at low temperature shows the hot electrons effect at high temperature result in this

    高溫下器件i - v特性曲線有上翹現象出現，低溫情況下未觀察到此現象，這是由於高溫下的熱電子效應所致。
  5. Based on the theory of thin - walled curved bar, reasonable hypothesized a third - ord parabolic curve, the paper adoptes variational method on energy, taking the coupled relationship of the effect of curvature radius, bend, torsion and shear - lag into consideration, establishes the elastic governing differential equation and boundary conditions for thin - walled curved box girders, which set the foundation of theoretical analysis of shear - lag effect in thin - walled curved box girders

    摘要文章以薄壁曲桿理論為基礎，合理地假設了三個剪力滯翹曲位移函數，應用能量變分法推導出考慮曲率半徑影響、彎、扭、剪力滯耦合的曲線箱梁彈性控制微分方程及其邊界條件，為薄壁大麴率箱梁剪滯效應建立了理論分析基礎。
分享友人
分享到 Line

分享到臉書