翻蓋控制 的英文怎麼說

中文拼音 [fāngěkòngzhì]
翻蓋控制 英文
flip-sns
  • 翻 : 動詞1 （變換位置; 歪倒; 反轉） turn over; turn around; reverse 2 （移動物體尋找） rummage; search...
  • 蓋 : 蓋名詞（姓氏） a surname
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. The ultra amusing ultra q remote control sweeps clear the vehicle, 1 to 8 proportions, 8 channels entire directions remote control, when advance backlash on the automobile body work lantern festival glitters, is concurrent music, the careful design remote control conforms to the kinesiology, the unique double throwout lever remote control way, on about remote control two throwout levers each control two powers wheels, slightly cause the vehicle the radius of turn to be more nimble, and marches forward when the vehicle simultaneously opens sweeps the plate to sweep clear and to turn fights controls remotely into the reality, sweeps the plate starts when also can send out delightful music, sweeps the plate also to be able control during rotation rocks, behind in the automobile body work theater box puts has continuously may skid and may open the cover the trash can, the trash can also may take out, turns fights may independently control remotely, the handling room vehicle door may start, the remote control is away from in the city surpasses 30 meters, the spacious area may achieve above 50 meters, holds controls nimbly is convenient, the luminous automobile body paint surface, works first - class, the use industry packs the ni - cd battery to take the power supply, may repeatedly charge 300 above time

    超好玩超q的遙控清掃車， 1比8比例， 8通道全方向遙控，前進後退時車身上的工作燈會閃爍，並發出音樂聲，精心設計的遙控器符合人體工學，獨特的雙推桿遙控方式，遙控器上的兩個推桿各控制左右兩個動力輪，使得車的轉彎半徑更小更靈活，並且在車行進時同時開啟掃盤清掃和翻斗遙控成為現實，掃盤啟動時也會發出悅耳的音樂聲，掃盤在轉動的同時還會左右晃動，車身後部的工作廂內放有一直可滑動並可開啟蓋子的垃圾桶，垃圾桶還可以取出，翻斗可以獨立遙控，操作室車門可開，遙控距離在城市中超過30米，空曠地區更可達到50米以上，操控靈活方便，光亮的車身漆面，做工一流，使用工業包裝ni - cd電池組作為動力源，可反復充電300次以上。
  2. Firstly using the calculated cutting contour to cut the drawing part, then flange on the flanging mould, and then check the error for flanging part. try - out the part until it is correct. it is shown that the error of calculated cutting contour is in the range of 1mm through compared it with the correct contour

    本文將實際調試出的合格零件的修邊線與採用誤差修正法計算所得的修邊線進行對比，其誤差均在1mm范圍內，對于型面極其復雜的翻邊零件，如后地板前板，其修邊誤差也可控制在3mm范圍內，這就有效地減少了汽車覆蓋件的修邊、翻邊調試次數和周期。
分享友人
分享到 Line

分享到臉書