翼型截面 的英文怎麼說
中文拼音 [yìxíngjiémiàn]
翼型截面
英文
aerofoil section-
Based on basic principles of grillage method, an improved grillage model of wide cantilevers bridge deck is brought forth and its effectiveness is verified after generalizing rules of grillage meshing and sectional characteristic
基於梁格法的基本原理，提出了寬翼緣上部結構分析的改進梁格模型，並總結了梁格單元劃分和截面特性計算的一般方法，最後通過算例驗證了該模型和方法的有效性。It is the key of ebfs, therefore, furthermore calculation about link are carried out in this thesis, introduced achieved research, summarized the affect of link on whole capability in the first, the second, numerical calculation are proceeded on link with ansys : with the purpose of discussing yielding mode critical length of link, established five different specimens ; with the purpose of discussing the influence of h / tw of web, b / tf of flange and h / b, established eighteen different specimens ; with the purpose of discussing the affect of stiffener, established four different specimens, and elaborated the affect of stiffener on link based on achieved test researches
因此，本文對耗能梁段進行進一步計算分析，概述耗能梁段對整體性能的影響，並利用有限元程序ansys對耗能梁段進行數值計算：針對耗能梁段的屈服類型建立5種不同長度的模型，計算討論耗能梁段屈服類型的長度劃分；針對耗能梁段腹板高厚比、翼緣寬厚比以及梁段截面形狀等因素共建立了18種模型進行計算分析；針對加勁肋對耗能梁段的作用建立了4種模型，並結合已有的試驗闡述了加勁肋對耗能梁段的影響。Abstract : a model of self - excited ae rodynamic forces acting on a sectionof bridge deck with additional surface atta ched below the trailing edge is established
文摘:首先建立了下風側附加翼板橋梁主梁截面的自激氣動力模型。The work in this thesis mainly includes following parts : 1. as for box girder cross section, the three - bar stimulation method under typical loads and supports has been introduced. the force and stress formulae for flanges have been derived from the three - bar method. by reasonable simplification for multi - cell box girder, the three - bar method has been applied in multi - cell box girder ' s shear lag analysis
對于箱形截面主梁，本文介紹了三桿比擬法上、下翼板中比擬桿的計算公式，以及在典型荷載和支承的情況下翼板內各桿的應力計算公式，並對多箱式主梁截面進行合理簡化，使三桿比擬法應用於多室箱梁的剪力滯分析。Second, change the diaphragm ’ s space between, retain the other thing, analyze the influence of the stress and deformation of box ? girder cross section and the beam web. based on the analysis upwards, the writer studied the rule of the influence of the stress and deformation box ? girder cross section and the beam web with different diaphragm ’ s space between. according to the results of finite element analysis, the writer puts forward some suggestions which will provide some reference for the following design
本文利用ansys有限元分析程序，對指定斷面，不同曲率的曲箱梁，建立完備的有限元模型，分別對二個方面的問題進行了分析:其一，通過對箱梁在有無跨中橫隔板時截面頂板及腹板的變形和應力分佈的對比分析，闡述了設置跨中橫隔板的重要性;其二，在相同工況下，通過改變橫隔板的設置間距，分析對箱梁翼緣及腹板的受力影響。分享友人