翼梁載荷 的英文怎麼說

中文拼音 [yìliángzǎihé]
翼梁載荷 英文
spar loading
  • 翼 : Ⅰ名詞1 （翅膀） the wing of a bird 2 （像翅膀的東西） the wing of an aeroplane etc : 鼻翼 wing of...
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. The work in this thesis mainly includes following parts : 1. as for box girder cross section, the three - bar stimulation method under typical loads and supports has been introduced. the force and stress formulae for flanges have been derived from the three - bar method. by reasonable simplification for multi - cell box girder, the three - bar method has been applied in multi - cell box girder ' s shear lag analysis

    對于箱形截面主梁，本文介紹了三桿比擬法上、下翼板中比擬桿的計算公式，以及在典型荷載和支承的情況下翼板內各桿的應力計算公式，並對多箱式主梁截面進行合理簡化，使三桿比擬法應用於多室箱梁的剪力滯分析。
  2. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  3. In elementary beam bending theory, it is assumed that the stresses are constant through the width of the beam. however, for the wide flange girders, the stresses are not uniform

    按照初等梁理論即假定翼緣板具有無限抗剪剛度，寬翼緣箱梁在荷載作用下翼緣的正應力沿著寬度方向上是均勻分佈的。
  4. After comparing between the finite - element analysis and experimental results, the author verified the fem. then according to the chinese code, the nonlinear finite model of the beam - to - column is established which are made of different size components. the responses of beam - to - column web moment connections which are made of different size components are compared and analyzed from three facets, and the conclusions about the joints behavior are drawn : thicken the connection plate, lengthen the connection plate or use a back - up stiffer can improve the connection behavior, consist of improving the behavior of load - supported and reducing the stress convergence in the flange moment plates

    本文根據我國規范的有關規定，自行建立了12個不同構件尺寸的樑柱腹板連接的三維有限元模型，對不同構件尺寸的樑柱腹板剛性連接節點在單向荷載作用下的反應進行了研究，從結構的mises應力等值線示意圖、梁端加載處的荷載? ?位移曲線、翼緣連接板兩端的mises等效應力以及翼緣連接板與柱相連接的三邊的mises應力等值線示意圖四方面進行了比較與分析，從而得出了不同構件尺寸的樑柱腹板剛性連接的在受力行為上的結論：增加翼緣連接板的厚度、增加翼緣連接板的長度以及採用柱的橫向加勁肋均可以改善節點的受力性能：提高節點的承載能力；減小翼緣連接板內部與柱翼緣邊的的應力不均勻現象，從而避免試件過早地發生破壞。
分享友人
分享到 Line

分享到臉書