耐折數 的英文怎麼說
中文拼音 [nàizhéshǔ]
耐折數
英文
folding number-
Considering the electrovalence, the curve of water consumption and the reliability of water supply, this paper respectively sets up the model based on the maximal flux and the model based on the expectation flux. it takes yearly expenditure converting value and yearly cistern converting value as target function and takes continuity equation, velocity of flow and compression resistance of cast iron pipeline as restrictions and sets up the pga model on optimal design of water supply networks
考慮到峰谷電價、用水量變化曲線及用水可靠性因素的影響，分別建立了以最高時流量設計管網的模型和以期望時流量設計管網的模型，以年費用折算值加上清水池年造價折算值為目標函數，以連續性方程、管中流速和鑄鐵管耐壓值等為約束條件，進行并行遺傳演算法對給水管網優化設計的實現。Experiments show the optimum content of pyrophyllite and dolomite is 30 % ; in contrast to original bond, the refractory point of bond is reduced by 55, the average coefficient of thermal expansion is reduced by 30 % and flexural strength and shock strength of grinding tool are increased by 27 % and 22 % respectively
通過實驗發現：葉蠟石和白雲石最佳含量為30 % ，與原結合劑相比，結合劑耐火度降低了55 ，平均熱膨脹系數降低了30 % ，磨具抗折強度提高了27 % ，磨具抗沖擊強度提高了22 % 。Refractory fiber and product is manufactured by means of dry method and wet method. as an excellent insulation material, it has comparatively low volume density, good softness and very low thermal conductivity coefficient. sticking method, ancjoring method and folding method can be selected respectively. this product can be used in various industrial kilns & furmaces for lowering heat consumption
耐火纖維及製品是採用干法、濕法生產的具有較低體積密度、較好柔軟性、極低的導熱系數的優質絕熱保溫材料，施工時可分別採用粘貼法、錨固法、折疊塊形式施工，適用於各種工業窯爐降低熱耗之用。The tests of e - o applications by our flux ktp has been realized, the results showed : optical waveguides fabricated by using an ion - exchange process, which have an exchange - ion concentration depth profile and refractive - index profile, is close to a complementary error - function distribution, optical homogeneity and device thermal stability is much better. amplitude modulation switch formed by our flux ktp has the contrast ratio of 150 : 1 and insert loss is 2. 5 % at 1064 nm. high quality optical pulse with 1 ns width was cut successfully by using an e - o modulator from a laser pulse with 50 ns width, this modulator had run for three years, and the crystal did n ' t blackened, it showed our low conductivity flux ktp can endure high modulation voltage for a very long time
Ktp晶體的電光應用試驗表明：用離子交換法製作的電光波導，其離子交換濃度、折射率變化符合餘弦誤差函數，光學均勻性以及器件的溫度穩定性較好；製作的強度調制電光開關，消光比為150 ： 1 ，對1064nm激光的插入損耗為2 . 5 ；製作的電光調制器用於激光脈沖整形試驗，從脈沖寬度50ns的激光脈沖削出脈寬1ns的高質量光脈沖，該電光開關經過長達三年多的使用，沒有出現晶體變黑現象，說明本實驗的低電導率ktp晶體能夠耐受長時間的調制電壓。The resistance attenuation of each element is considered in the design process, and the statistical parameters of the elements are assumed to be the same as the investigated results of china. in the process of the calculating of the element reliability attenuation in expected service life, several load combination and different load ratio of dead load to live load are considered. in order to ensure that structure reliability in expected service life satisfies the requirement of today ’ s code, a method of choosing the initial reliability index of structure basing on the length of expected service life and the structure resistance attenuation is proposed and the corresponding durability reduction factor is chosen by an optimum algorithm
根據我國現行建築結構可靠度設計原理，考慮耐久性退化影響因素，設計了抗力統計參數與我國調查結果一致的五種代表性鋼筋混凝土構件，考慮多種荷載效應組合以及不同荷載效應比，研究了不同使用期內代表性構件的可靠度變化規律;為保證預期使用期內結構可靠度水平仍可滿足現行規范要求，提出了根據預期使用期和抗力衰減幅度確定結構設計可靠度指標的方法，並通過優化的方法確定了預期使用期內的耐久性折減系數，給出了預期使用期結構可靠度設計的實用設計方法。分享友人