自由配平法 的英文怎麼說

中文拼音 [zìyóupèipíngfǎ]
自由配平法 英文
free to trim method
  • 自 : Ⅰ代詞（自己） self; oneself; one s own Ⅱ副詞（自然;當然） certainly; of course; naturally; willin...
  • 由 : causereason
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 自由 : freedomliberty
  1. The basic thought of the csapfba algorithm is : the edge routers perform the state management per flow, and the edge routers differentiate between the marked flows and the non - marked flows, and the edge routers insert the relevant information into the packet header by using dynamic packet state ; the core routers divide the output link bandwidth into two parts in the light of the state information of the packet header by using class - based queueing, and the core routers allocate proportionally the bandwidth to the marked flows according to their service profiles and the current network load, and the core routers allocate the bandwidth to the non - marked flows according to the principle of max - min fairness, and the csapfba algorithm can adaptively dynamically adjust the bandwidth allocation between the marked flows and the non - marked flows

    本文在csfq演算法的基礎上，提出了一種核心無狀態的自適應的成比例公平帶寬分配csapfba （ core - statelessadaptiveproportionalfairbandwidthallocation ）演算法。 csapfba演算法的基本思想是：在邊界路由器完成基於每個流的狀態處理，將所有的流分成標記流和非標記流兩種類型，採用dps技術將有關信息編碼進分組頭；在核心路由器根據分組頭中攜帶的狀態信息採用cbq策略，將輸出鏈路帶寬分成兩部分，對標記流根據當前的網路負荷按照服務規格成比例地分配帶寬，對非標記流按照最大最小公平性原則分配帶寬，並且能自適應地動態調整帶寬分配的比例。
  2. In this paper, the so preparing self - compacting concrete with low and middle strength using super fine mountain sand artifical sand and phosphorus slag is studied systemically. through the study the influence of the shape, the proportion of the dust and the grade of sand to the workability and the mechanical property of self - compacting concrete, it is found that super fine mountain sand artifical sand are not suit to prepare low and middle strength self - compacting concrete, but when they are combined and the additive and assistant band material are used, c20 - c40 high performance self - compacting concrete is prepared ; the corresponding additive is developed to solve the delamination caused by the low proportion of banding material ; the evaluating system for the workability of low and middle strength self - compacting concrete is built ; the controlling method for production, construction and curing was set up. and the result of the research is applied into several projects

    通過分析特細山砂和機制砂的顆粒形態、粉末含量、顆粒級配等特性對自密實混凝土的工作性能和力學性能的影響，發現特細山砂、機制砂不宜單獨用於配製中低強度等級自密實混凝土，宜將特細山砂和機制砂進行合理復配，並選擇合適的外加劑和礦物摻合料，優化配合比設計，可生產c20 c40中低強度等級自密實高性能混凝土；研製開發出了具有高效減水、保塑、抗離析功能的外加劑，有效解決了中低強度等級自密實混凝土由於膠凝材料用量少而出現的離析、泌水問題；應用正交設計方法，對因素和水平進行合理選擇，確定了生產中低等級自密實混凝土的最優配合比；建立了中低強度等級自密實混凝土的工作性評價體系；提出了生產、施工及養護的質量控制技術方法。
  3. A planar sidm with j loops ( expressed in term of smj ) can be regarded as comprising of a sidm with j - loops ( expressed in term of smj - 1 ) and a dyad ( expressed in term of dyadj ). then, the circuit condition of sm, is determined by the circuit condition of smj - 1 and the configuration of dyadj. based on the above thought and combined with the automatic generation of structural decomposing of planar mechanism according to the type transformation theory, circuit automatic identification of planar sidm are realized, two examples are given to demonstrate the use of this method

    具有j個環路的sidm可看作由j - 1個環路sidm與一個雙桿組（記作dyad _ j ）組成，則sm _ j的迴路情況由sm _ （ j - 1 ）的迴路情況、 dyad _ j的構形以及dyad _ j與sm _ （ j - 1 ）運動的相互作用決定，基於此思想，在全面分析了所有類型雙桿組的構形及裝配條件的基礎上，與型轉化法機構結構分解路線的自動生成相結合，實現了平面sidm迴路識別的系統化與自動化；最後給出了兩個分析實例。
  4. Second, the edge points on the scan - lines of the first prewarped image are detected and the corresponding points on the same scan - lines of the other prewarped image are matched. third, with these corresponding edge points, the scan - lines of the two images are segmented. in the end, more exact corresponding relation of these points are obtained under the use of the affine transformation and the auto - corresponding of the images are finished

    該演算法首先矯正源視圖，使矯正後圖像滿足視點平移關系；然後檢測第一幅圖像掃描線上的邊緣點，再由這些邊緣點匹配出第二幅圖像上對應的邊緣點，利用這些對應的邊緣點再分割兩幅圖像中所對應的掃描線；最後用仿射變換建立較為準確的點與點的對應關系，完成圖像的自動匹配。
分享友人
分享到 Line

分享到臉書