荷載交叉線 的英文怎麼說
中文拼音 [hézǎijiāochāxiàn]
荷載交叉線
英文
load cross line-
Then the coupling beams with new reinforcement layout were made an inquiry into, and the improvement on the seismic behavior by coupling beams diagonally reinforced with a few rows in end regions was found out at last, based on the observations of the experimental phenomena and the analysis of the measurement result, and by the comparison of seismic behavior by making use of hysteretic response, ductility and energy dissipation behavior, a conclusion is presented : the code for design and construction of reinforced concrete high - rise structures ( the draft asked for advise hi 2000 ) ca n ' t ensure that the coupling beams have fairly good seismic ductility ; the result of improvement of the seismic ductility of the coupling beams by the increase hi stirrups besides the strengthen of longitudinal detailing reinforcement was n ' t obvious ; the coupling beams diagonally reinforced with a few rows in end regions have fairly good mechanisms, and the ductility and the behavior of energy dissipation are better than conventionally reinforced concrete coupling beams, so it is suitable to te tised in short coupling beams
本文通過對三根小跨高比（均為l h = 1 . 0 ）剪力墻洞口連系梁在低周反復荷載作用下的試驗，了解了嚴格按《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）設計的連梁具有的抗震性能，研究了採取增大連梁配箍量同時加強縱向構造筋的方案對抗震性能的影響，並進一步對新的配筋形式的連梁進行了探討，了解了在連梁梁端配置多排交叉斜筋方案對連梁抗震性能的改善。通過對試驗現象的觀察和量測結果的分析，利用荷載?位移滯回曲線、延性和耗能性能等指標對各個試件的抗震性能進行了比較，最後得出結論： 《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）不能保證小跨高比連梁具有較好的抗震延性：通過增大連梁配箍量同時加強縱向構造筋的方案對改善連梁的抗震延性的效果不太明顯；梁端配置多排交叉斜筋的連梁具有相對較好的受力性能，其延性和耗能性能等各項性能指標均優于普通配筋連梁，宜在深連梁中採用。By the dynamic stress test, the stress spectrum of cross sustaining device ' s weaking section is obtained, then the loads of cross sustaining device for the speed increased freight car in utilizing condition is identified, which offer the foundation for the load of the fatigue test
摘要通過動應力測試得到交叉支撐裝置疲勞薄弱部位在線路運行中的應力譜，從而識別出提速貨車交叉支撐裝置在運用工況下的載荷，為其室內疲勞試驗加載提供依據。The cross short rollers guide way and servo feed - system are the most important parts of 3mz204cnc bearing internal grinding machine made by luoyany bearing research institute. - we have analysised firstly the factor of influence with roller guide way rigid, and we have obtained a load - distortion curve. we also have analysised the dominating factors influence with distinguish ratio of guide way, and we have obtained a solution about pre - tighted load which were tested by experiments
本文對洛陽軸承研究所研製的3mz204cnc全自動內圓磨床的核心部件：十字交叉滾子導軌和數控進給系統展開研究，首先對影響滾動導軌剛度的因素進行分析，得出載荷?變形曲線，對影響導軌解析度的各因素進行分析，得出預緊力大小與分佈對解析度和起動力的影響，並通過實驗驗證。
分享友人