荷載傳處 的英文怎麼說
中文拼音 [hézǎizhuànchǔ]
荷載傳處
英文
load transfer-
The main components of the latter are multi - rib sandwich panels, including floor slabs and wall slabs. reinforced concrete conformation columns are set where the longitudinal walls and latitudinal walls intersect and copulative beams are set where floor slabs and wall slabs intersect. they play a role of linking and transferring loads, bearing a small part of loads at the same time
無骨架體系的主要承重構件是密肋夾芯板（包括樓板和墻板） ，縱、橫墻相交處設鋼筋混凝土構造（連接）柱，墻板和樓板相交處設連系（圈）梁，連系梁和柱主要起連接和傳遞荷載作用，也承擔少部分荷載。Because uav is smaller and lighter than normal plane, the miniature aerial rs system is easily effected by wind, its " stabilities of position and stance are not good. because the load of uav is so finite, the large professional aerial photogrammetry camera can not be installed
微型無人機遙感由於受到無人機平臺體積小、重量輕、任務載荷有限等因素的制約，在飛行作業中傳感器位置和姿態受氣流影響大、穩定性差，而且目前是非專業攝影機成像，這些都大大增加了其影像幾何糾正處理的復雜性。The temperature effect which has been calculated is taken as " thermal load " forced on the body, then such thermal stress is settled as general elasticity mechanics question ; secondly, the thermal stress is taken as " surface force " forced on the body, and the new system stiffness is formed which include the extra stiffness matrix, then it changes the nature frequency of the structure
首先，這篇論文介紹溫度場和熱應力場的有限元方法，建立了三維熱傳導模型計算有溫度場產生的熱應力，計算熱應力時運用了一種轉化思維：將溫度處理為「溫度載荷」 ，這樣就能用彈性力學問題的處理方法來求解熱應力。其次，將熱應力作為結構的「面內力」 ，而面內力產生附加的幾何剛度矩陣，改變了結構的剛度，影響了結構的固有頻率。However, it is too expensive in investment, complex in experimental techniques, difficult and dangerous in performance. in this paper to overcome these drawbacks, the similarity relations together with a new method and its principle of experiment have been developed based on the model theory of structural similarity. according to this principle, the total stress ; an be obtained as a sum of the stresses due to weight and external loading, which based on only one model experiment without any gravitational loading
最後，針對外載與自重共同作用下，傳統光彈性分析法中採用離心力場模擬重力場獲得自重應力的試驗投資耗費大、技術復雜且難度大和不安全等嚴重缺點，按照結構相似的模型理論，本文提出模型外載與自重並存變動外載的光彈性分析法，導出處理這個問題具體的相似律和試驗原理及方法，進行了典型實驗驗證，指出僅用外載作用的模型試驗，即不用離心力場模擬重力場的模擬試驗，就可以獲得上述兩種載荷共同作用下的應力分析結果。In this paper, single fiber composite fragment ( sfc ) method, which is one of the most widespread and effective experimental methods for determining the mechanical properties of interface, was adopted to study the load transfer mechanism and to evaluate the adhesion performance of composite with surface - treated fibers. this is helpful for optimization design of interface
本文採用了目前最為流行、最為有效的直接測定界面力學性能的實驗方法之一? ?單纖維復合材料斷裂實驗研究了纖維樹脂界面載荷傳遞機理，分析了幾種纖維表面處理復合材料界面的粘結情況，對界面的優化設計具有一定的指導作用。It applies an interval method to select element in the evolutionary structure optimization method ( eso ), and recovers or deletes element by the “ birth and dead ” function of element. another method viewed as second order smoothing technique for suppressing the checkerboard patterns has been proposed based on the filtering function ’ s principle. then the above methods are applied to solve a temperature - controlling problem in the steady heat conducting field and a multi - objective topology optimization problem considering multiple load cases and coupled effect
本文基於ansysparametricdesignlanguage （ apdl ） ，提出漸進結構法中應用區間法進行單元的篩選，通過單元「生死」的功能實現單元的恢復與刪除，根據濾波函數法原理提出修改的二階棋盤格處理方法，並就穩態熱傳導溫度控制問題，考慮熱、力耦合的多載荷工況的多目標拓撲優化設計問題進行求解。Load transfer mechanism of tubular pile is not expatiated completely because of the complex mechonism of soil core, which restricts the development of the theory for the bearing capacity of pile and its practiceal application
筒樁具有與一般的灌注或沉管實心樁不同的荷載傳遞機理，筒樁的荷載傳遞機理的復雜性制約了筒樁承載理論的發展與工程應用，其工程設計方法至今仍處於半理論半經驗的狀態。This article aims at the characteristics of a baibie harbor great bridge, by the spot construction test and mechanicses, limited an analysis, dissolve to the construction technics and loading capacity, stake deliver mechanism, bearing stratum and glazing rock depth area curve etc. s of the borehole cast - in - place concrete pile in the karst terrain do the some study research
國內外對于巖溶地區鉆孔灌注樁的研究，主要是針對具體工程的施工方案描述和施工故障及處理措施，對巖溶地段基樁的承載機理及承載力的綜合研究則未見報道。本文針對白墅港大橋的特點，通過現場施工試驗及力學、有限元分析，對巖溶地區鉆孔灌注樁的施工工藝、荷載傳遞機理、持力層厚度及嵌巖深度等方面做一些探討性研究。It takes good use of these two numerical computation methods merits and it is valuable for defmiting the computation model of pile ? oil ; at the same time, it builds the computation model of compound pile foundation and uses the software ansys which is about finite element to build the mechanics model. in regular quality soil, the result worked by this way has good unanimity with traditional results, so it applies us strong evidence for using the way which this article tells us to solve problems which is difficult to handle in compound pile foundation, such as irregular quality, layer quality of the soil. at last, taking foundation soil ' s measuring data of liaoning technology university ' s test building for example, and using the way this article tells us to build compution module, we solve the sharing ration of pile and loading board
本文利用有限元與邊界元耦合的方法求解樁土相互作用問題，充分利用兩種數值計算方法的優點，對確定樁土相互作用計算模型是一次有益的嘗試；同時建立了群樁相互作月的數學模型，並利用有限元分析軟體ansys建立其力學模型，在均質土體中取得了與傳統解答較好的一致性，從而為拓展利用本文所述建模方法，解決群樁作用機理研究中難以處理的土體成層、非均質等性質，提供了有力的根據；最後，以遼工大實驗館地基土實測資料為例，利用本文建模方法，求解出承臺與樁的荷載分擔比，對安全、經濟地進行群樁基礎設計具有重要指導作用和應用價值。Simultaneity, various single fiber strength tests ( sft ) and the single fiber fragmentation techniques were discussed, and the influence of fiber surface treatment on the single fiber strength and the interface load - transfer were discussed in detail. the two parameters weibull statistic theory was used to evaluate the scattering of the tensile strength test results of three types of single fibers with different surface treatments. the following conclusions can be drawn based on the analysis of the results
同時，文中詳細討論了單纖維強度測試實驗（ sft ）和單纖維復合材料斷裂實驗（ sfc ） ，重點討論了纖維表面處理對單纖維拉伸強度和界面載荷傳遞能力的影響；採用兩參數weibull統計理論對經過三種不同表面處理的單纖維拉伸強度的測試結果的分散性進行了評價，獲得了理想的實驗結果；分析實驗結果可得到如下結論， sft實驗與sfc實驗獲得的界面剪切強度吻合良好；經過表面處理的玻璃纖維的界面粘結情況較未經處理的玻璃纖維好；經過表面處理的玻璃纖維的界面粘結強度和單纖維拉伸強度均高於未經表面處理的玻璃纖維。The one - dimension model has the advantages of simplicity, convenience and feasibility, but it also has one serious shortcoming, i. e., the influence of material properties on the load - transfer ability of the interface was not taken into account. although the two - dimension interface model considered the transverse effects of the matrix and the effects of the material properties on the load transfer ability of the interface, its principle is very complicated, and is n ' t fit for dealing with the data of the sfc test
Cox的一維界面載荷傳遞模型的主要特點是簡單、方便和實用，但是具有一個致命的缺點：沒有考慮材料性能參數對界面載荷傳遞能力的影響； nairn的二維界面載荷傳遞模型雖然考慮了基體的橫向效應、纖維基體材料性能參數對界面載荷傳遞能力的影響，但是其原理非常復雜，不適合於單纖維復合材料斷裂實驗的數據處理。Based on the basic requirements and function of the displacement - load sensor, the design adopts single - chip 8 - bit microcontroller - p89c51rc2 manufactured in an advanced cmos process and belonged to the 80c51 microcontroller family to make the p89c51rc2 ’ s circuit less, simple and more reliable
根據位移-載荷傳感器功能和主要技術指標要求，採用高性能靜態80c51設計的，帶有非易失性flash的8位微處理器p89c51rc2作為傳感器的核心控制器。A method of choosing the wind load influence modulus that decides the wind load numerical value of combination structure was proposed correspondingly. firstly the wind load parameter that influences the wind load of combination structure was chosen according to design criterion of high - rising structure and through tradition calculation methods of wind load. by using currently calculation methods the axis force and martix of the most danger section was worked out, and the security of structure was analyzed and checked
首先運用傳統風荷載計算的方法，結合本文的組合結構的特殊情況，以高聳結構設計規范為參考，參照風荷載理論選定了影響該組合結構風荷載的風荷參數，並依據一般塔架演算法（簡化懸臂梁法）計算出了與底座連接處斷面（最危險截面，距塔底6米段）的軸力和彎矩，同時對此處進行了應力分析和可靠性校核。For three - short - pier shear wall under vertical loads, the results remain the same, and transfer beam at this moment will work with the middle pier, constituting a t - shape beam to sustain the moment and axial tensions together. 4. under the horizontal loads, the inner stress distribution in the frame supported short - pier shear wall shows similarities with that of the short - pier shear wall underneath the fastened supports
4 、水平荷載作用下，框支短肢剪力墻墻肢內的應力分佈形式接近於下部固支的短肢剪力墻的應力分佈;轉換梁承受上部墻肢傳遞的拉力、剪力和彎矩，當短肢剪力墻墻肢數量較多時，轉換樑上、下邊緣拉、壓應力交替出現，剪應力的最大值處于洞口下方的轉換梁體內。Assuming the load on the plate is transmitted in distributional state to the foundation, on the basis of the relationship between the nodal force and its displacement on the semi - infinite surface, the relationship between the distributional forces on the foundation surface and the nodal displacements is developed by use of the gaussian integral method
假設板上荷載按分佈力形式傳遞到地基中，根據半無限空間上某節點力與該處的位移關系，用高斯積分法建立了地基表面分佈力與節點位移關系表達式。Aimed to the two deficiencies of three - ring gear transmission, the dissertation will analyze these two aspects. the first, according to the finite element model of gear pair of three - ring gear reducer, the dissertation is aimed to analyze the multi - tooth meshing effect of three - ring gear reducer using finite element method, and the number of teeth contacted simultaneously, their load distribution characteristics and the von mises stress change are gained
針對三環減速器以上兩點的不足之處，本文將對以下兩方面進行分析:首先，本文以三環減速器齒輪副有限元模型為研究對象，利用有限單元法對三環減速器多齒嚙合效應進行分析，得到三環減速器傳動時的實際接觸齒數、嚙合齒載荷分配以及vonmises應力變化規律。I also do some exploration to the resisting features of powdery earth and the factors affecting the load transforming of pile in the powdery earth layer through this big test. please point out my mistakes in this thesis
同時，對粉性土的土抗力特徵及其影響粉類土層中樁的荷載傳遞性狀的有關因素，以及對進行過高應變測試后又進行了低應變完整性檢測的斷樁進行了淺顯的分析，疏誤之處，敬請指正。The algorithmic difference compared with the traditional one is that this arithmetic is independent of pre - load ( consolidation stress ) and can calculate the primary consolidation effect and assess the unloading feasibility straightforwardly
與傳統的演算法不一樣的地方是這些演算法與預壓荷載（即固結應力）無關系，直接計算出主固結的效果及評價預壓排水固結地基處理卸載的可行性。The peculiar mechanical character about pumping liquid concrete is discussed. based on the supposition that the ability of transferring hydraulic pressure of liquid concrete is orthotropic and the friction forces exists between concrete and steel tube, the pressure formulas of liquid concrete and the allotting formulas of deadweight are reasoned out. a new method is brought forward for allotting deadweight of liquid concrete during simulation analysis in pumping - core - concrete construction phase, which improves the calculation precision
在探討泵送液態混凝土的特殊的力學性質基礎上，在假定液態混凝土傳遞壓強能力為正交各向異性、混凝土與鋼管壁之間的存在有摩擦力的前提下，推導出液態混凝土壓強公式和自重荷載的分配公式，提出了在進行鋼管內混凝土灌注過程的施工模擬分析時處理液態混凝土自重荷載分配的合理方法，從而提高施工模擬分析的計算精度。This paper has the following deficiencies : 1, the dynamic load of the gear transmission is neglected in the numerical calculations ; 2, the results of this paper are in need of being verified by the experiments
本文的不足之處在於: 1 、數值計算中尚未考慮齒輪傳動中的動載荷特性; 2 、缺乏實驗驗證。分享友人