荷載多邊形 的英文怎麼說
中文拼音 [hézǎiduōbiānxíng]
荷載多邊形
英文
load polygon-
Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。The sea1 ring with complex section shape cafl be treated as a combined body made of several individual cy1 inders with di fferent dimensions. by app1ying the method used in the " edge prob1 em " of the fnoment theory of she11, the deformat ion - - - radia1 disp1acement and rotation at the two edges of each individual
應用殼體力矩理論中求解邊緣問題的方法，將密封環分解為多個等厚度、截面為單一矩形的筒體，對每一圓筒進行分析並運用殼體力矩理論求出其兩個邊緣在外載荷作用下的邊緣變形值? ?徑向位移及轉角。The buckling and ultimate strength of ship plating normally depend on a variety of influential factors, namely geometric / material properties, loading characteristics, initial imperfections ( i. e. initial deflections and residual stresses ), boundary conditions and corrosion, fatigue cracking
船體板的屈曲和極限強度取決于很多影響因素，主要有：板的幾何尺寸、材料特性、載荷特徵、初始缺陷（如初始變形和焊接殘余應力） 、邊界條件以及腐蝕的影響、疲勞裂紋等。The rayleigh - ritz method is used to lead to analytical expressions for the stiffness and mass matrices and load vector as well as their sensitivities, which uses the simple polynomials to define assumed displacement functions, geometry and construction of wing structures. excluding some selected terms from the displacement functions or using stiff springs at the specified locations imposes boundary conditions. the accuracy of calculated results is improved by including transverse shear effects and using multiple sets of ritz functions in the analysis
它使用簡單多項式作為ritz基函數、定義翼面的幾何和結構參數，利用rayleigh - ritz方法導出翼面結構的剛度矩陣、質量矩陣和載荷向量及其靈敏度的解析表達式，通過排除位移函數中某些選定的項或在指定點使用約束彈簧施加各種邊界條件，考慮橫向剪切變形和使用多組ritz基函數改進分析的質量，使用等效蒙皮和等效夾芯技術提高計算效率。For three - short - pier shear wall under vertical loads, the results remain the same, and transfer beam at this moment will work with the middle pier, constituting a t - shape beam to sustain the moment and axial tensions together. 4. under the horizontal loads, the inner stress distribution in the frame supported short - pier shear wall shows similarities with that of the short - pier shear wall underneath the fastened supports
4 、水平荷載作用下，框支短肢剪力墻墻肢內的應力分佈形式接近於下部固支的短肢剪力墻的應力分佈;轉換梁承受上部墻肢傳遞的拉力、剪力和彎矩，當短肢剪力墻墻肢數量較多時，轉換樑上、下邊緣拉、壓應力交替出現，剪應力的最大值處于洞口下方的轉換梁體內。分享友人