蓋板焊 的英文怎麼說
中文拼音 [gěbǎnhàn]
蓋板焊
英文
bridge welding-
Welded - in deck screw caps for filling and sounding pipes
充料管與探測管用焊接蓋板螺紋蓋The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed
再現分析得出的主要結論為：橋架的主樑上蓋板主焊縫的最大應力超過了許用應力，但小於屈服極限，可以繼續投入使用；副梁內部的應力遠遠超過了強度極限，變形特別嚴重，不能滿足生產要求，因此更換新的副梁；端梁內部的應力超過了屈服極限，小於強度極限，在應力較大的位置焊接補強板；投入使用后，要對整個橋架進行定期檢查。Single sided - fpc this product is pressed with one layer of flexible copper - clad panel and one layer of flexible solder coating
柔性單面線路板是由一層柔性覆銅板和一層柔性阻焊覆蓋膜壓合而成。This paper analyzes the repairing feature on perforating casing and presents a new procedure that the root of perforating hole is covered by a little block age plate and then repair welding is carried out
通過對射孔槍管修復特點的分析，提出了先利用小堵板蓋住射孔眼的根部，再進行補焊的新工藝，實現了槍管的重復利用，為油田同類產品的修復提供了寶貴經驗。It is made of quality steel plate, which is stretched forming welded and plastic sprayed with bubble cement filled in its inner cavity. its pedestal is plated with zine and cast aluminum alloy, which height is adjustable and can be self - locked
線槽蓋板，地板採用優質鋼板經拉深成型點焊噴塑內腔填充發泡水泥填料，支座為鍍鋅結構，高度可調並能自鎖。This voltage transformer has three poles and the iron is made of sheet. the body is fixed on the box cover by clamping. there have the primary and secondary bushing also on the box cover
本系列電壓互感器的鐵心由條形矽片疊成，為三柱芯式，器身用鐵夾件固定在箱蓋上，在箱蓋上裝有一次及二次套管等，油箱用鋼板焊成，油箱壁下部裝有接地螺栓及放油塞，箱底有四個安裝孔。Plug screws and flat sealing rings for welded - in screw caps for filling and sounding pipes
充料管和探測管用焊接蓋板螺紋蓋的螺塞和扁密封圈Specification for the design, testing, and utilization of welded - wire rack decking
焊接線架蓋板的設計檢驗和利用規范This product is a result of the developing of more and more complicated circuits. it can be made by pressing solder coating to both sides of a double - sided copper - clad panel
雙面柔性電路板是隨著線路的不斷復雜化而誕生的，可以由雙面覆銅板同時壓制兩面的阻焊覆蓋膜製造而成。Shipbuilding. locking handles for round flat hatch covers. welded bolt with packing
造船工業.平甲板艙蓋用閉鎖柄.帶壓緊墊片的焊接銷Via comparing chinese specification with aisc specification, some important factors that must involve in the design of floor system consisting of composite slab and composite beam are complemented. the two most important is the shape of formed steel deck that can be used in composite slab and the design shear strength of welded stud shear connectors
在組合樓蓋體系設計中，筆者通過對中、美兩國規范、規程的對比，對在中國規范、規程中未曾明確提出卻需要在組合樓蓋設計中加以考慮的一些因素進行了說明，其中最主要的是壓型鋼板的選型依據和焊釘抗剪承載力的影響因素。分享友人