虛圓面 的英文怎麼說
中文拼音 [xūyuánmiàn]
虛圓面
英文
spurious disk-
In this thesis, the technology of visual fictitous design was used to design the level exchanged direction and double direction plough. first, the traction force formula of cylindrical plough face based on the prior study was deduced, and the forces of the solid model of circumrotatory pin was calculated, and visual dummy design technology was applied to analyse the force of circumrotatory pin and the parameter of pin
其次在前人研究的基礎上推導出圓柱型犁體曲面的牽引阻力公式；根據該公式計算出旋轉銷三維實體模型所受的力，根據該力運用可視化虛擬設計技術對模型進行受力分析，對旋轉銷的參數進行合理設計；根據牽引阻力公式計算出安全螺栓所受的力，根據該力運用虛擬設計技術對安全機構進行設計。When analyzing the principle and performance of the lsdll, circular flowgraph is used. the expression for " penalty " time and mean and variance of the acquisition time is derived from the circular flowgraph of large step acquisition method
在理論方面，本文利用圓形狀態圖對大步進快速捕獲法的工作原理進行研究和分析，導出由相關處理時間、大步進時間、虛警概率、檢測概率和虛警「代價」時間表示的捕獲時間平均值及其方差的表達式。In the paper, based on the method of low pair replacing with high pair, the problem of cam design was transferred to that of linkage design. by means of rotary unit vectors, the equations of displacement, velocity and acceleration of the replacement mechanisms were developed. and then, the virtual linkage ' s length and direction were deduced
論文基於高副低代原理，將平面凸輪機構設計與再現函數的平面連桿機構設計統一為同一種方法，運用圓向量函數建立代換機構的位移、速度、加速度矢量方程式，求取虛擬連桿桿長和方向，由此展開凸輪理論廓線、實際廓線、曲率半徑和壓力角的求解，並得出用圓形刀具加工凸輪時刀具中心的軌跡方程。This paper presents the images of circular points of the plane on which the 1d object translates, the constraints of circular points to camera intrinsic parameters, and the numerical solution to the constraints equations ( and then we obtain the camera intrinsic parameters )
摘要給出了平移運動的一維物體所在平面的虛圓點圖像及其對攝像機內參數的約束，和約束方程的數值求解方法，從而獲得攝像機的內參數。Curve traced on an imaginary sphere with the source at its center and joining all the points corresponding to those directions in which the luminous intensity is the same, or a plane projection of this curve
在一個以光源為圓心的虛擬的球面上，將光源射向球體上光強相同的各方向的點用線連接起來，就成為等光強曲線。This paper analyzes and discusses the problems involving the design of the electronic control ( ec ) and numerical control ( nc ) systems for a new type nc grinder - machine used to grind planar quadratic and annular enveloping worms based on novel four - axis - interpolation, in which a central fabricating method is introduced
摘要本文作者設計了新型四聯動平面二次包絡蝸桿數控磨床的數控及電控系統，該磨床採用虛擬中心的方法，通過兩正交軸的圓插補及磨頭基座的自轉實現了傳統蝸桿加工磨床上的砂輪工作面的平面回轉運動，克服了傳統加工蝸桿工作層面多，結構復雜，加工精度、效率低等缺點。Starting from two well - accepted assumptions in theory of thin - walled beams, a general theory for linear analysis of curved beams with any open sections is established in this paper by using the principle of virtual work. the equations of equilibrium and natural boundary conditions are given
文章首先從薄壁構件理論的兩個基本假定出發，利用虛功原理，建立起一套精確的、可以應用於任意開口薄壁截面圓弧曲梁的線性理論，給出相應的平衡方程和邊界條件。To the noise, singular point, non - face area and the division of face area, this dissertation proposes filter, segmentation by clustering and area combination methods respectively ; to the detection of oriental faces in color images and complex context, the author combines the skin - color model based face rough detection and the ellipse based face location methods to one, then verify the candidate face by abstracting face features. experiment indicates that this algorithm is feasible and highly efficient
針對類膚色區域中的噪聲、奇點、非人臉區域以及人臉區域被割離的情況，本文提出了濾波、聚類分割、區域合併等演算法；針對人臉非人臉區域的的分割，修改並採取了橢圓模板定位的方法；針對「候選人臉」中出現的「虛警」問題，首先提取人臉面部特徵，然後採取人臉驗證演算法加以驗證。分享友人