蝸形模型 的英文怎麼說
中文拼音 [xíngmóxíng]
蝸形模型
英文
cochlear model-
Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3
通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3The software uses two entity configuration methods : extruding and simulating entity cutting in realizing three dimensional configuration, which successfully achieve three dimensional configuration of involute columnar vertical gear, involute columnar helical gear, standard vertical spline, archimedes worm and disco - cam
軟體在三維造型功能實現上使用了拉伸和模擬實體切削兩種實體造型方法，成功地實現了漸開線圓柱直齒輪、漸開線圓柱斜齒輪、標準直齒條、阿基米德蝸桿和盤形凸輪的三維造型。Under opengl environment, we use four - side grids to reconstruct a worm surface and gain a solid modeling of worm. under the computer virtual reality environment, we simulate the manufacturing process of dual generating method
在此基礎上，在opengl編程環境下，以四邊形網格構造蝸桿理論型面，以邊界表示法中的半邊數據結構表達蝸桿實體，獲得蝸桿的三維實體模型及其型面數據。On the basis of analyzing application situation of cad / cae / capp technology at home and abroad, this paper brings forward the research direction ? integration and intellectualization combining the expert system. by the analysis of the characteristic of each part of worm gear, this paper upbuilds the characteristic model of worm gear based on the restriction and actualizes data transmission and information sharing among cad, cae and capp. this paper analyzes the general principle of parameter determination and strength check about worm gear and researches the algorithmic of strength check based on the characteristic about worm gear. this paper introduces expert knowledge into respective procedure of cad, cae and capp and actualizes the intellectualization in design process, strength analysis and process planning. on the basis of aforementioned research, this paper develops the cad / cae / capp integration software of gear components by means of the active - automation technology provided by autocad and vb. the applic ation of the software indicates this system has perfect function and project applied cost
本文在分析cad / cae / capp技術在國內外應用概況的基礎上，結合專家系統，提出了智能集成的研究方向。以蝸桿傳動的各個零件作為研究對象，在分析了各自特徵的基礎上，利用數據庫技術和圖形單元建模技術，建立了蝸桿傳動的特徵模型，實現了cad / cae / capp之間的數據傳輸和信息共享；分析了蝸桿傳動中參數確定、強度校核的一般原則，進行了基於特徵的蝸桿傳動強度校核的演算法研究；將專家知識融入在cad 、 cae 、 capp各個過程中實現了設計過程、強度分析和工藝分析的智能化。在上述研究的基礎上，利用autocad2000提供的activexautomation技術，以vb為開發工具，開發出了蝸桿傳動的cad / cae / capp集成軟體。分享友人