螺旋槳旋轉面 的英文怎麼說

中文拼音 [luóxuánjiǎngxuánzhuǎnmiàn]
螺旋槳旋轉面 英文
propeller piston
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 槳 : 名詞1. （劃船用具） oar; paddle 2. （螺旋槳） propeller
  • 轉 : 轉構詞成分。
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 螺旋槳 : [機械工程] screw propeller; propeller; screw; blade; airscrew; propeller screw; propelling screw...
  • 螺旋 : 1 （具有螺紋的圓柱體 屬于斜面類的簡單機械） corkscrewspin; screw; spiral; helix 2 （螺旋現象;尾旋...
  • 旋轉 : revolve; gyrate; rotate; spin ; revolution; revolvement; rotation; circumgyration; circulation
  1. In this dissertation, through computer simulation, the problems of modeling, control and guidance of auvs are presented. the first part of this dissertation addresses the problem of dynamically modeling of auvs, and derives thrusters " two - dimension nonlinear dynamic model, which has axial flow speed and propeller rotational velocity as two state variables, voltage or current of motor as inputs, and thruster force and torque as output. the second part focuses on the nonlinear adaptive sliding mode control of auvs in diving plane and steering plane

    本論文系統研究了自主式水下航行器的建模、非線性自適應滑模控制、以及深度調整和水平面導引方法等問題，具體成果和創新點如下1 、根據流體力學理論，建立了螺旋槳推進器的動態模型，它以螺旋槳來流速度v _ p和螺旋槳轉速n為狀態變量，以電機施加轉矩為輸入，螺旋槳推力t和轉矩q為輸出。
  2. The lifting - line and lifting - surface design method, the harmonic analysis method based on the panel method, new section design ways, the effective operating curves are integrated into a whole design system of the unsteady propeller, the design system is effective and reliable by the design example, the model test and the application to the full scale ship

    本文把升力線和升力面設計方法、基於面元法預報螺旋槳非定常性能的諧調分析方法，新剖面設計方法、有效運轉曲線計算方法組合為一套完整的非均勻流場中螺旋槳設計計算系統，經實例設計和模型試驗及實船的應用，該設計系統是可靠且有效的。
  3. A mathematic model of the motor is builded and emulated through matlab. the low - speed and constant - torque, high - speed and constant - power state is analyzed and researched, also the software approach of simulation to the driver has been done, a digital signal processor tms320lf2407 is developed successfully to control the perm square - wave bldcm driving airscrew of solar powered unmanned engine. it is useful to the further study

    在matlab下建立了電機的數學模型，通過計算機模擬，驗證了數學模型的正確性，同時在理論上對低速恆轉矩高速恆功率運行進行了分析與研究，提出了一種用模糊控制的方法實現恆功率控制，並對驅動器進行了系統模擬，成功的研製了以數字信號處理控制器tms320lf2407為控制核心的驅動器，控制無刷直流電動機驅動太陽能無人飛機的螺旋槳，為後面繼續研究工作提供了參考。
  4. This paper presents a design method of propeller blade section operating in non - uniform flow field and an idea of equivalent operating curve with unchanged cavitations characteristic on blade section, the method for selecting the curve is set up

    摘要給出了非均勻流場中螺旋槳槳葉剖面的設計方法，提出了保持剖面空泡特徵不變的等效運轉曲線的思想，並創建了等效運轉曲線的確定方法。
  5. The primary purpose of this paper is how to solve the overloaded propeller ' s condition. the style of propeller trailing edge cutting and shave on the pressure surface is adopted. the propeller ' s actual effect pitch will be reduced which cause the propeller ' s torque down

    本文主要是考慮螺旋槳出現負荷過重時如何處理的問題，所以採用槳葉隨邊切割並在葉面處將翼型修順的方式，實質上是切割后導致螺旋槳實效螺距的減小，從而使螺旋槳吸收的轉矩降低來達到主機負荷降低的目的。
  6. The thruster contained a large - diameter, slowly rotating blade with nozzles that diffused the propulsive flow, minimizing the churning that would otherwise disturb the caked silt

    機器的推進器包含了大直徑慢速轉動的螺旋槳，而且推進水流由噴嘴送出，以避面劇烈攪動擾亂了結塊的淤泥。
分享友人
分享到 Line

分享到臉書