螺末 的英文怎麼說
中文拼音 [luómò]
螺末
英文
acorn nut-
This twin screw extruder has the feature of one - side circumgyrate , it ' s an ideal equipment for the small - scale factory who produce powder
該擠出機是同向高速旋轉雙螺桿結構,是用於多種組份物料經一定的溫度在熱狀態下達到最佳的理想效果,適應小型企業生產粉末的理想設備。Leaves crowded near apex of the trunk, spirally arranged ; stipes dark brown, with sharp spines ; lamina large, oblong, tripinnate ; pinnae 17 - 20 pairs, alternate, longest one to 60 cm long, the basal one reduced ; rachis short - spiny ; pinnules 18 - 20 pairs, sessile or nearly so, lanceolate, to 10 cm long and 2. 5 cm wide, divided almost to the costa ; segments more or less falcate, toothed
葉螺旋狀排列,聚生於莖端;葉柄棕色,具銳刺;葉片大,長矩圓形,三回羽狀深裂;羽片17 - 20對,互生,最大的長達60厘米,基部一對縮短,羽軸有短刺;小羽片18 - 20對,無柄或近於無柄,披針形,長達10厘米,寬2 . 5厘米,深裂幾達中脈;末回裂片多少鐮狀,有齒。The bottom edges of the endplates are mated to another winglike device, the lower main plane, which in turn is attached to the rear crash structure ? a carbon fibre cone bolted onto the gearbox
終板末端邊緣被設計成與另一個翼狀地設備相配合,這個翼狀設備是一個較低的平面,附著在尾部碰撞結構上? ?變速箱上面的碳纖維錐形螺釘。Far out in the uncharted backwaters of the unfashionable end of the western spiral arm of the galaxy lies a small unregarded yellow sun
在銀河系西螺旋臂的末端那片未曾標明的寂靜虛空中,懸掛著一顆不被人注意的小小的黃色太陽。The westland wyvern was the last fixed - wing aircraft design from the westland aircraft co. and was one of the last prop - driven fighters
「飛」攻擊機是威斯特蘭公司設計的最後一種固定翼飛機,是一種末代的螺旋槳戰斗機。After the valve has been adjusted to its balance set point and without moving the handwheel, remove the retaining bolt from the end of the handwheel using a 1 / 4 " allen wrench
在閥門調整到平衡點,並且沒有旋轉手輪后,採用一把1 / 4 "通用扳手從手輪末端拆卸固定螺栓。Square head bolts with short dog point
短螺栓末端的圓柱軸頸止端的方頭螺栓Before installing, be sure pipe ends are reamed and threads are cut to size
在安裝之前,要確保管道末端經過鉸孔,螺紋長度切割適中。Before installing the valve, be sure that the pipe ends are reamed and threads are cut to size
在安裝閥門之前,要確保管道末端經過鉸孔,螺紋長度切割適中。Slightly fry flour in oil until brown, put in the radish pieces and soup, bring to the boil, add condiments and transfer to a plate. steam the clam meat until done, transfer to the plate
蒜薑末嗆鍋後放入香糟花菇筍片,倒入鹵汁,再放螺片,顛炒后裝盤即成。The micromanipulator must contact the objects to be handled in the manipulation process and the end - effector will be loaded by the exterior forces. the static mechanics of the manipulator has been analyzed on the basis of the work done above, by the way of the screw theory the mechanics jacobia is educed, furthmore, the matrix is the transpose of the kinematics jacobia in such a microscopic world. meanwhile the index of the static stiffness and payload related to the mechanics is studied
微動機器人在操作過程中,必然要接觸到操作對象,末端執行器要受到力力矩的作用,在前面分析的基礎上,進一步分析其靜力學性能,運用螺旋理論導出反映其靜力特性的力雅克比矩陣,並且可以看到此矩陣與速度雅克比互為轉置。同時還考察了微動機器人的靜剛度、承載能力指標。Hydrophobicity analysis of the noeb showed that it is a transmembrane protein and includes four transmembrane regions at n - terminal., consisting of three primary helixs and one secondary helix
疏水性分析發現, noeb是一個跨膜蛋白,在n末端有4個跨膜區,其中包含3個初級螺旋和1個次級螺旋。Remove stem nuts ( 22 ). keep stem from turning by inserting screw driver in slot on end of stem
拆卸閥桿螺母( 22 ) 。通過在閥桿末端的槽內插入螺絲刀來避免閥桿旋轉。Using three - dimensional particle trajectories dispersed droplet diameter at the outlet of screw element during compounding in a co - rotating intermeshing twin - screw extruder was computed
摘要用物料三維流動路徑結合分散模型計算了螺紋元件出口處分散相液滴的直徑,分析了螺桿轉速、擠出機產量和液滴初始直徑對末端分散相液滴直徑的影響。After the valve has been set to the correct balance point, record the setting. without turning the handwheel, remove the retaining bolt from the end of the handwheel
在正確設置閥門的平衡點后,記錄下設置值。不需要旋轉手輪,直接從手輪末端拆卸固定螺栓。The variation of the operating condition did not change the distributive range magnitude of the dispersed phase droplet
螺桿轉速和擠出機產量的變化對末端分散相液滴直徑的分佈范圍影響不大。Non soldering compression fittings with cutting ring - run t - stud with taper threaded stud end not for new design
帶有切割環的非焊接壓縮配件.帶錐形螺紋末端的活動tNon soldering compression fittings with cutting ring - elbow stud with taper threaded stud end not for new design
帶有切割環的非焊接壓縮配件.帶錐形螺紋末端的肘形螺Non soldering compression fittings with cutting ring - branch t - stud with taper threaded stud end not for new design
帶有切割環的非焊接壓縮配件.帶錐形螺紋末端的分支t分享友人