螺栓壓模 的英文怎麼說
中文拼音 [luóshuānyāmó]
螺栓壓模
英文
bolt die-
Dead weight loading simulating that of the bolts was applied at the bolt holes through the agency of steel balls and buttons.
螺栓荷載是用死荷重來模擬的，以鋼球和壓鈕作為代用件，通過它們將此荷載施加於螺栓孔。In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented
本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block
在上模節流棒槽內裝入節流棒，將節流棒調節螺栓裝配進節流棒的螺絲孔中，再裝配上壓塊。In the design of articulation hole bolt, the blur variable and random variable existing at the same time, the blur reliability design method of shear strength and extruding strength are approached
探討了在鉸制孔用螺栓設計中，模糊變量與隨機變量同時存在時，抗剪強度與擠壓強度的模糊可靠性設計方法。On the basis of the finite element analysis of the press - mounting machine, to solve the modeling error of the previous modeling method, a new mixed - model method using the spring element and thin - layer solid element was introduced in this thesis. an experiment designed to test the interface static stiffness was carried out and the needed modeling datum was obtained
在對壓裝機進行了整體建模模擬的基礎上，針對壓裝機整體建模存在的誤差問題，本文提出了一種改進的彈簧單元和薄層實體單元混合建模的方法，並依此設計了螺栓結合面靜剛度測試試驗，通過試驗獲得了建模所需的參數。Engineering drawing system can draw two dimension curve graphs, main detail drawing and assembly drawing. the curve of internal trajectory and dynamic simulation of particle external trajectory. the detail drawing includes the graph of chamber, grain design, connection body, nozzle, some standard part
工程繪圖可以繪制二維曲線圖和零部件圖，其中二維曲線包括有內彈道壓（推）力?時間曲線、質點外彈道動態模擬曲線；零部件圖包括有標準螺栓與螺紋孔、燃燒室結構圖、裝藥設計截面圖、連接底結構圖、噴管結構圖及火箭發動機總體裝配圖。The program fearpv is applied to analysis the sealing structure of the pressure vessel model during the total process, including bolt pretensioning process, heating and compression process, thermostated heating and constant pressure process, and the cooling and decompressing process
應用反應堆壓力容器瞬態密封有限元分析程序對反應堆壓力容器模擬體密封結構進行了螺栓預緊、升溫升壓、恆溫恆壓、降溫降壓等全過程分析。分享友人