螺線形導線 的英文怎麼說
中文拼音 [luóxiànxíngdǎoxiàn]
螺線形導線
英文
fish-line conductor-
The company passed iso9001 in 2001 : 2000 international quality management system attestations. now the predominant product has already become xr series helical gear units, xf series parallel shaft helical gear units, xk serial helical - bevel gear units, xs series helical - worm gear units, xt series spiral bevel gear units, xb series high power gear units, xh series high power gear units, nmrv series worm gear units, mb, mbn series planetary friction mechanical speed variator, x, b series cycloid reducer, wb series cycloid micro reducer to wait more than ten serieses, several thousand kinds of specificationses of in general use product
現主導產品已形成xr系列斜輪硬面減速機xf系列平行軸斜輪減速機xk系列斜輪螺旋錐輪減速機xs系列斜輪蝸輪減速機， xt系列螺旋錐輪減速機， xb系列螺旋錐輪-斜輪減速機xh系列平行軸斜輪減速機nmrv系列蝸輪減速機， mb mbn系列行星錐盤無級變速機， x b系列擺線針輪減速機， wb微型擺線針輪減速機等十幾個系列數千種規格的通用產品。The experiment procedure and analysis result about exteriorly extended end - plate connection with high strength bolt are introduced primarily ; each sample ' s dimension is given. the adding load equipment, measuring apparatus placed, measuring point established is detailed. adding load measure load and m - curve is produced ; the single span gabled frames horizontal displacement formula is deduced when the horizontal concentrated force is applied to it
重點介紹了外伸端板高強螺栓連接的實驗過程及實驗分析結果，介紹了各組試件的形狀尺寸、加載裝置、測量儀器安放、測點的布置等；給出加載方式及測出的m -曲線；計算出試驗節點的初始剛度；推導水平集中力作用下單跨門式剛架考慮節點半剛性的側移計算公式。Harmonized blank detail specification for lead screw actuated non - wirewound preset potentiometers - square form, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel, rigid terminations - assessment level s
導螺桿傳動非線繞預調電位器協調空白詳細規范.正方形的容器密閉的與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器剛性終端.評定級別sBased on the method of limitation analysis of soil plasticity, researching from the soil arching mechanism of soil - nailing retaining, the upper limit of the critical height of soil - nailing slopes and the minimum horizontal length from coping of the potential slide surface to the edge of deep excavation are obtained through the analysis to weight of soil and vertical loading and the mechanism of soil and soli - nailing acting reciprocally
摘要基於土的塑性極限分析方法，以均質土坡為例，從土釘支護結構的準粘聚力理論出發，綜合考慮土體自重、坡頂的條形荷載，以及土釘與土體的相互作用的機理，推導出了土釘支護的臨界高度的上限值和潛在螺旋曲線滑動面在坡頂方向距基坑邊沿的最小水平距離解析表達式，可供基抗支護設計參考。The stability of the helical equilibrium is analyzed with phase plane method, and an analytical criterion of stability is revealed
用相平面法分析螺旋線平衡的穩定性，導出解析形式的穩定性條件。The surface panel method has been applied to predict the hydrodynamic performance of highly skewed propeller. the surface of propeller and its trailing vortex are discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution. for highly skewed propeller, the conventional method generating grid oriented along constant radii will result in a high aspect ratio and a high skewness and a twist panel near the propeller tip on blade surface, which result easily in incorrect calculation results of velovity on blade surface, even in iteration divergence and calculation failure. a “ non - conventional grid ” is developed to acoid these problems. this grid can effectively solve the problem of the calculation and convergence for highly skewed propeller. the non - linear kutta condition of equal pressure on upper and lower at the trailing edge is executed by the iterative procedure. by sample calculating, the obtained results are satisfied the experimental data
採用面元法預報大側斜螺旋槳水動力性能，螺旋槳表面及尾渦面離散為四邊形雙曲面元，每個面元上布置等強度源匯和偶極子分佈.對于大側斜螺旋槳而言，槳葉表面採用常規的等半徑網格劃分方法在近葉梢處將導致大展弦比、大側斜和扭曲面元，這容易使槳葉表面速度的計算結果不正確，甚至會導致迭代過程發散及計算失敗.文中建立了一種「非常規網格」劃分方法，能有效地解決大側斜螺旋槳的計算和收斂問題.槳葉隨邊處通過迭代實現非線性等壓庫塔條件Fish line conductor
螺旋形導線( b ) the linear fluid model is used to study the conductor - centered helical groove twt. we have analyzed the effects of the beam parameters on the gain and the bandwidth of the twt
（ 2 ）我們用線性理論模型研究了具有中心導體軸的矩形螺旋槽行波管內的注-波互作用特性，對電子注參量對小信號增益和帶寬的影響進行了分析。分享友人