螺釘調整 的英文怎麼說
中文拼音 [luódīngdiàozhěng]
螺釘調整
英文
screw adjustment- 螺 : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
- 釘 : 釘動詞1. (用釘子固定) nail 2. (用針線縫) sew on
- 調 : Ⅰ動詞1 (配合得均勻合適) harmonize; suit well; fit in perfectly 2 (使配合得均勻合適) mix; adju...
- 整 : Ⅰ形容詞1 (全部在內; 完整) whole; all; complete 2 (整齊) neat; tidy; orderly Ⅱ動詞1 (整理; 整...
- 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
-
This system collect and deal with the input and output electric signal from optical pick - up itself, adjust floating bolt and adjustable resistance, make the specification of the optical pick - up attain the demanded data
通過對激光頭輸入、輸出的電信號進行採集和處理,調整激光頭上的浮動螺釘和可調電阻,使激光頭的各項性能標達到規定值。Idle mixture screw
怠速混合氣調整螺釘It only needed a minor adjustment : a turn of a screw here, a little tightening up there, a drop of oil and it would be as good as new.
它只需小小的調整而已:這里擰擰某個螺釘,那裡上緊些,滴上一滴潤滑油,這樣它就和新的一樣了。Slotted set scews with cup point
蝶形端開槽調整螺釘As far as i could see, it only needed a minor adjustment : a turn of a screw here.
就我所見,它只需小小的調整而已:這里擰擰某個螺釘。5. no parts and components warranty will be delivered if customer or non - warranty - taker dismantles disassemble and adjusts parts, assembly of the diesel and components that are not allowed to be adjusted such as injection pump assembly lead sealing, and reassembles them within the warranty term, which however, fails to meet technology demand such as torque and advance angle of major bolts, resulting in failure and damage of relevant components, assembly and parts
在保修期內,顧客或非承擔保修者拆卸解體調整柴油機的部件總成和規定不得調整的部位如噴油泵總成鉛封等,重裝后又未達到技術要求如重要螺釘的扭矩噴油提前角等,導致部件總成和相關聯零部件失效和損壞,由此涉及的零部件Install the assembly sensor on the distributor support seat assembly, regulate the clearance between sensor and rotor up to requirement, and then fasten bolt
將總成傳感器安裝在分電器支承座總成上,調整轉子與傳感器間隙符合規定后,緊固螺釘Align sensor iron core with distributor timing rotor with a clearance between 0. 25 0. 4mm, then fasten the bolt
調整傳感器鐵芯正對分電器正時轉子,間隙在0 . 25 0 . 4mm間,然後緊固螺釘How to adjust the gap between the upper and lower blades. loss the screw first, then turn the handle to what you need, then fasten the screw again
間隙調整時需將鎖緊螺釘松開,然後轉動手柄至所需的刻度值,再將鎖緊螺釘鎖緊。Release rod usting screw
分離推桿調整螺釘Slotted set scews with cone point
錐端開槽調整螺釘As far as i could see, it only needed a minor adjustment : a turn of a screw here, a little tightening up there, a drop of oil and it would be as good as new.
就我所見,它只需小小的調整而已:這里擰擰某個螺釘,那裡上緊些,滴上一滴潤滑油,這樣它就和新的一樣了。Adjusting screws for cables for controls
控制鋼絲繩的調整螺釘If there is any mistake, please loosen the screws to adjust them, then tighten the screws up
如有誤差,應略為松開螺釘進行調整,然後擰緊螺釘。Fast idle screw
快怠速調整螺釘Release lever usting screw
分離桿調整螺釘Ustable stop screw
可調整止動螺釘Slotted set scews with flat point
平端開槽調整螺釘Anti, shutdown screw
防不滅車調整螺釘Extreme idle screw
極限怠速調整螺釘分享友人