行斜率 的英文怎麼說

中文拼音 [hángxiélǜ]
行斜率 英文
line slope
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 率 : 率名詞（比值） rate; ratio; proportion
  1. The fourth chapter introduces the theory of fractional brown movement ( fbm ). the image texture of turning workpiece is analyzed using fbm model. after abstracting the texture character, the cutting tool wear status can be determined according to fractal dimension and average slope of the fitting curve of the logarithm power spectrum

    第四章採用分數布朗運動（ fbm ）的基本理論，對切削工件表面紋理的圖像進行分析，提取紋理特徵參數，根據分形維數和圖像上對數功率譜的擬合曲線的平均斜率來判斷刀具的磨損狀態。
  2. For rotor steel ( 30crlmolv steel ), the tests of low - cycle fatigue property are done under different temperatures. the fatigue life under different temperatures is researched to make up for the defects of the testing for foreign similar materials. when pull - stretch data is attempted to evaluate low - cycle fatigue data, the result shows that four - point associated method in middle - low life zone is done well under room temperature, but there are large errors of four - point associated method and general - slope method under other temperatures

    在本文中，通過與國外同類材料的性能進行比較，國產材料與國外材料共有的材料特徵基本相同；對轉子鋼（ 30crlmolv鋼）進行了不同溫度下的低周疲勞性能實驗，研究其在不同溫度下疲勞壽命，以彌補國外對同類鋼材測試的不足；採用拉伸數據預測低周疲勞壽命時發現，室溫條件下用四點關聯法在中低壽命區預測較好，在高溫條件下四點關聯法和通用斜率法都有較大誤差，需要進行改進。
  3. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  4. The adsorption isotherm of neptunium on silica gel correspond to the form of langmuir isotherm. according to clausius - claperon equation, from the slope in inkd vs 1 / t plot, adsorption heat could be estimated. from the data of adsorption heat it is concluded that the adsorption of neptunium on silica gel in nitric acid solutions belongs to chemical adsorption and the adsorption process is an endothermic reaction

    三種價態的鎿在硅膠上吸附的等溫線符合蘭格繆爾吸附等溫線的形式，是單分子層吸附；根據克勞修斯-克拉柏龍方程，以1nkd對1 t作圖，通過直線斜率計算出吸附熱，從吸附熱的數據可判斷三種價態的鎿在硅膠上的吸附屬于化學吸附，是吸熱的過程；對npov ） 、 np （ v ）和np （ vd在硅膠上的吸附進行了比較，提出了三種價態的鋒在硅膠上吸附的機理。
  5. According to the geometry of slope measurements for the subjective wavefront optometer, a wavefont reconstruction model using zernike polynomial with normalization factor is put forward. based on householder transformation and gram - schmidt orthogonalization method, two methods for working out unknown zernike coefficients are bring forward. the error propagation parameter for the wavefront reconstruction model is deduced

    深入研究了帶標準化因子的zernike多項式的性質;針對主觀式像差儀波前斜率采樣方案，提出了採用帶標準化因子的zernike多項式對眼測試波前進行重建的數學模型;提出了兩種求解方法，即基於householder變換求解法和基於gram - schmidt正交化求解法，用於確定重建模型中的未知模式系數;推導出了該波前重建模型對斜率測量誤差的傳遞系數。
  6. The detailed works are as follows : the finding patterns problems in the time - series data sequence are described, and a new trend logic expression method is introduced, and its algorithm and experiment result of algorithm are given ; time - scries data are disposed, and using the arctg. slope of line as the sample of pattern recognition, so ignoring the aberrance of pattern in the classified. in addition, a new time - series pattern finding algorithm based on higher - order neural network is put forward

    同時給出了本文的具體的工作，主要是：對在時序數據序列中發現模式問題進行了描述，並介紹了一種新的趨勢邏輯表示方法，給出了其演算法及演算法的實驗結果；對時序數據進行處理，提出了利用線段的斜率反正切值作為模式識別的樣本，從而在分類時忽略模式的畸變；另外，還提出了一個新的基於高階神經網路的時序模式發現演算法。
  7. The curves of the consolidation settlement in soft clay base of flood land are gained, which compare the effect of sand drain. the settlement - time curves in different period are also gained, which increase the height of embankment to 8m, based on the test data of hang - yong highway. furthermore, the consolidation settlement characters of these entity engineering are analyzed, and, the variation rules of the rate of grade and degree of the curves in different period in the whole section, the maximal settlement and the liner regression relations between the rate of grade and degree are calculated

    本文利用大變形固結有限元分析程序（ lscfea ）中的小變形平面固結分析單元（ sse2 ） ，結合實體工程項目進行了地基固結沉降的有限元計算，分別得出河灘相軟土地基在考慮砂井和未考慮砂井作用下的固結沉降曲線及杭甬高速公路試驗段在高堆載情況下的固結沉降曲線；並對以上曲線特徵進行了分析，得出各時間段曲線斜率、角度在整個斷面的變化規律，以及沉降最大值與斜率、角度變化之間的線性回歸關系。
  8. Based on the hydrodynamic energy transport model, the influence of variation of negative junction depth caused by concave depth on the characteristics of deep - sub - micron pmosfet has been studied. the results are explained by the interior physical mechanism and compared with that caused by the source / drain depth. research results indicate that with the increase of negative junction depth ( due to the increase of groove depth ), the threshold voltage increases, the sub - threshold characteristics and the drain current driving capability degrade, and the hot carrier immunity becomes better in deep - sub - micron pmosfet. the short - channel - effect suppression and hot - carrier - effect immunity are better, while the degradation of drain current driving ability is smaller than those with the increase of depth of negative junction caused by source / drain junction shallow. so the variation of concave depth is of great advantage to improve the characteristics of grooved - gate mosfet

    基於能量輸運模型對由凹槽深度改變引起的負結深的變化對深亞微米槽柵pmosfet性能的影響進行了分析，對所得結果從器件內部物理機制上進行了討論，最後與由漏源結深變化導致的負結深的改變對器件特性的影響進行了對比.研究結果表明隨著負結深（凹槽深度）的增大，槽柵器件的閾值電壓升高，亞閾斜率退化，漏極驅動能力減弱，器件短溝道效應的抑制更為有效，抗熱載流子性能的提高較大，且器件的漏極驅動能力的退化要比改變結深小.因此，改變槽深加大負結深更有利於器件性能的提高
  9. Used fourier transforming the nuclear logs, its vertical resolution can be achieved from analyzing the changes of amplitude spectrum slope

    摘要對核測井曲線進行付氏變換，其縱向解析度可以從分析振幅譜斜率變化中獲得。
  10. He finds the pitch range after calculated the three important parameters through the bladed for windows software, then presents an optimized control strategy that regulate the pitch angle in terms of the wind speed. it must control the output power because the variational output power brings the variational loads. he confirms and optimizes the control strategy that the output power is the control target, the output power is divided into three parts

    將功率作為系統控制的目標，將功率分成三段進行控制，在低風速區，載荷是有限的，以功率最大化作為控制目標；在額定風速附近，由於處在升力曲線斜率的變化點，功率變化較大，應盡快調整槳距角進入失速區工作，減少載荷的波動，該額定風速區的上下工作點要通過現場試驗的手段來確定；在額定風速以上，使功率維持在額定輸出，減少功率波動，並通過bladed軟體的模擬計算對控制策略進行了驗證。
  11. The centroid position of the focal spot directly depending on intensity distribution and phase slope distribution of near field is derived, and its physical meaning is described

    進一步推導了焦斑質心位置對光束近場強度分佈和相位斜率分佈的依賴關系式，並對該式清晰的物理意義進行了闡述。
  12. The paper brings to light the value of the different sub - objectives contributing in the function of financial synthetic objective in a financial synthetic profit model through analyzing the volumes and slopes of the two - dimensional vector. the theoretical basis of the synthetic profits of enterprises participating inte rnational securities market financing has been brought out

    同時構建了融資綜合收益理論模型，並對該模型進行二維向量分析，通過對二維向量的模和斜率的分析，揭示了企業融資綜合收益模型的融資目標函數中各子目標函數權重對其貢獻的大小。
  13. At the doppler centroid aspect, this paper make use of maximum value method ; energy method and autocorrelation function method to estimate doppler centroid. at the doppler frequency aspect, this paper make use of image offset method ; time - frequency method ; minimum entropy and fractional fourier transformation method to estimate doppler frequency rate

    在多普勒參數估計中，採用了最大值法、能量法和自相關函數法進行多普勒中心頻率估計;採用了圖像偏移法、時頻分析法、最小熵法和分數階傅里葉變換法進行多普勒調頻斜率估計。
  14. Using the variational method, analytical conditions for stationary pulse propagation in dense period fibers with strong dispersion management are deduced. the expression of initial soliton peak power is given. by employing the obtained formulas, the soliton evolution semi - analytically in various dispersion maps can be investigated. effects of the third order dispersion are also studied in this paper. the results show that imperfect dispersion slope compensation can cause pulse central position shift and even serious degradation of soliton shape

    利用變分方法，推導出了在強色散管理的密集周期光纖中脈沖穩態傳輸的解析條件，並給出了初始脈沖峰值功率的表達式.運用這些公式，對各種色散管理系統中孤子的演化進行了半解析的考察.三階色散也被考慮在內.結果表明:不完善的色散斜率補償將導致脈沖中心位置的偏移甚至嚴重的孤子形狀劣化
  15. The main purpose of this paper is to realize the section properties and moment capacities of profiled sheets by experimental study and academic analysis for three types of profiled metal sheets which are called u450, u860and super combination profiled metal sheets produced by shanghai baosteel metallurgical construction corporation. its main contents include : ( l ) according to " european recommendations for the testing of profiled metal sheets ", the moment capacities of 32 full - size u450 and u860simple and continuous specimens are tested. ( 2 ) using the finite element program ansys and nonlinear finite element method, the moment capacities of super combination profiled metal sheets profiled are analyzed

    主要內容有： （ 1 ）依據《金屬壓型鋼板試驗歐洲建議》 ，進行了32塊1 : 1的u450 、 u860二類壓型鋼板試件簡支、連續板彎曲性能試驗研究； （ 2 ）採用有限元程序ansys對超級組合壓型鋼板受彎性能進行了非線性有限元分析，分析中考慮了大變形與幾何初缺陷，得出其荷載?撓度曲線與極限荷載p _ （ max ） ，通過截面特性與曲線斜率、極限荷載的關系式得到截面特性；並將分析結果與同濟大學試驗結果進行對比分析。
  16. Introduces some anti - seepage high embankment dams in the world with bitumen concrete inclined core wall, and analyzes, taking the existing maopingxi embankment dam as an example, the effect of slope thereof on the stress and deformation of the wall by non - linear adhesive elastic finite element calculation changing the type and thickness of the core wall

    摘要介紹世界上幾座瀝青混凝土斜心墻防滲高土石壩，並結合國內已建的茅坪溪瀝青混凝土心墻壩，通過改變其心墻形式和厚度，並用非線性粘彈性有限元對其進行計算分析，探討了斜心墻的傾斜斜率對心墻的應力與變形的影響。
  17. On the basis of the research by former people, the work of this paper includes several aspects as follow : throughout a great deal of experiment of the mechanics performance of 2d weave c / sic composite materials laminated plate, we simulated the nonlinear relationship between a and e in the tensile course ; and we inspected the original damages and the damages evolvement ; and we made the statistic analyses of the tensile strength. some important conclusions have been given in the paper

    主要有以下幾個方面：在大量二維編織c sic復合材料力學常規性能的實驗基礎上得到了拉伸實驗中卸載點和卸載模量，卸載模量和加載斜率，加載斜率和應力等之間的關系，並在此基礎上得到了模擬同種材料拉伸曲線的非線性的應力?應變關系；配合我們的實驗過程進行初始損傷和缺陷的檢測以及實驗過程中材料損傷演化過程的動態無損檢測；對我們現有的二維編織c sic復合材料拉伸強度數據進行了分佈擬合。
  18. Based on the theory of mfl and a study on the signal characteristics ofac - mfl and ect : on one hand, it expouded the flaw identification model of “ slope ratio ” todetect the defects in panel, rob or pipeline ; on the other hand, the flaw - depth measurementmethod based on the characteristical frequency were used in ac - mfl. the application ofac - mfl was realized, and it showed the accordance of defect detection for these twotechniques

    從其檢測原理出發，在與上述渦流檢測信號特點進行比較的基礎上，一方面，利用「斜率比值」識別模型實現了對板材、管材、棒材等表面缺陷的檢測;另一方面，利用交流信號的信息實現了基於拐點頻率的深度測量方法在該技術中的應用。
  19. Based on the discussion the peculiarity of computer identification of tectonic soft coal seam, implemented the computer automatically identification of tectonic soft coal seam with well log of coal seam using the method of stratifying with slope - variance and probability statistics

    摘要在對構造軟煤分層計算機識別的特殊性進行探討的基礎上，應用斜率方差分層、概率統計計算的方法，實現了煤層段的測井曲我對構造軟煤分層的計算機「自動」識別。
  20. Based on traditional dtw speech recognition and through relaxing extreme, limiting route ' s slope and improving some routes, the system can recognize and respond quickly especially when applied in small vocabulary speech recognition and speaker - dependent recognition

    在傳統的dtw語音識別的基礎上，通過放寬端點、對路徑進行斜率限制和改進路徑限制等方法，使系統能夠快速的識別響應，尤其是對于小詞匯量和特定人識別，可以有效地提高響應速度和識別率。
分享友人
分享到 Line

分享到臉書