行波光電管 的英文怎麼說

中文拼音 [hángbōguāngdiànguǎn]
行波光電管 英文
traveling-wave phototube
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 波 : Ⅰ名詞1 （波浪） wave 2 [物理學] （振動傳播的過程） wave 3 （意外變化） an unexpected turn of even...
  • 光 : Ⅰ名詞1 （照耀在物體上、使人能看見物體的一種物質） light; ray 2 （景物） scenery 3 （光彩; 榮譽） ...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  1. However, the manufacture process of twt is so complicated that many kinds of subject, such as electron optics, magnetics, cathode electronics, microwave electronics, electronmagnetic fields theory, material science, mechanics and calorifics are involved in

    行波管的研製涉及到電子光學、磁學、陰極電子學、微波電子學、電磁場理論、材料學、機械與熱分析諸多學科，工藝過程十分復雜。
  2. By successful solution of non - linear magnetic fields and revision of the program, we can reach following conclusions : in the computation of nonlinear magnetic fields, if iteration method is used, under - relaxation is necessary when amending the permeability distribution in soft magnetic materials ; and when < wp = 5 > calculating the equivalent current density in permanent magnets, under - relaxation is not a necessity ; when searching for permeability values by interpolation method on the demagnetization curve of soft magnetic materials, if a fixed saturation point is set, around this point an abrupt change of permeability values will be obtained ; this sudden change may cause a little problem in the smoothness of magnetic field distribution ; because the magnetic circuits of microwave tubes are too complicated, in the author ' s view, to describe the working state of a magnet system, the working points of magnets can not do it properly but average energy production of magnets will serve ; as to indicate the quality of a magnet system design for microwave tubes, the efficiency of magnetic energy utilization will be a very good criterion

    由此得出結論，在非線性磁場計算中：採用迭代法的情況下，在各迭代循環之間進行磁導率修正時，一個欠鬆弛迭代過程是必需的；對永磁體中的等效電流修正時可以不作欠鬆弛迭代；在純鐵的磁化曲線上指定某一個固定的磁感應強度為磁飽和值，會使得插值求出的磁導率在該磁飽和值附近有一突變，這一突變對計算結果中磁場分佈變化的光滑性稍有影響。在微波管磁系統設計中，由於微波管磁路比較復雜，作者認為磁體的工作點並不能很好地反映磁體的工作狀態，而採用平均磁能積為衡量磁體工作狀態的標準更加符合微波管磁系統的實際情況；要表示磁系統設計好壞的程度，則用磁能利用的效率為標準更好。
  3. According to the test conditions, the double polarity inputting mode is adopted in the circuit of voltage - frequency converting part ; storage batteries are used in the optical emission part of optical fibre isolating and transmitting device, that can guarantee isolation between the main circuit and the testing system ; the 89c51 singlechip is used in the singlechip testing - controlling unit, the peripheral circuits are extended, data are transmitted through the serial port in this part ; the p opular software delphi5. 0 is used in the pc part, the communication between singlechip and pc by serial port, plotting of current wave, regulation of data ; the optical - electrical isolating and triggering are used in the controlling part, this can guarantee the veracity and reliability of breakers triggered, this triggering mode is also used in the triggering of the main closing breaker, the tested breaker and the assistant breaker, the triggering signals are sent out by a singlechip

    壓頻轉換部分電路中根據實際情況採用了雙極性輸入方式；光纖隔離傳輸裝置的光發射部分電源採用了蓄電池供電，確保了主迴路與測試迴路的完全隔離；單片機測控部分採用了89c51單片機，擴充了外圍電路，通過串口向pc機傳送數據； pc機與單片機之間的串口通訊、波形繪制、數據管理等都採用了軟體delphi5 . 0編寫。該測試系統中預留了輸出口，可以對合成迴路中的主合閘開關、被試開關、輔助開關進行觸發，信號由單片機發出，控制部分採用了光電耦合隔離觸發的方法。軟體設計主要集中在對電流信號的數據採集、數據處理、數據傳送、人機界面、波形繪制和數據管理，軟體部分又可分為單片機和pc機程序設計兩大部分。
  4. We introduced particularly a series of methods for improving reliability, disturbance resistance, scanning scope and location precision, such as : using modulate laser, designing bandpass filter, zooming out signals and using a special circuit to get rid of disturbances. after that, the effective signals enter into the spring - circuit and touch off it, then the data register lock the codes, so the codes are read into single chip and are sent to the computer for the location. finally, many experiments about disturbance resistance, scanning scope and location precision have been done

    為了提高導航定位系統的可靠性、抗干擾性、掃描范圍及定位精度，使其具有良好的穩定性，而採取了一系列技術措施，包括：採用調制激光信號；設計帶通濾波器和信號的整形處理電路；採用門限技術剔除干擾；並採用單片機系統對採集到的各類信號進行綜合處理與管理；建立了基於合作路標的位置計算方法和數學模型，實時通過串列通訊送到上位機，以便上位機對數據進行處理，從而進行定位計算。
分享友人
分享到 Line

分享到臉書