表面冷凝器 的英文怎麼說

中文拼音 [biǎomiànlěngníngqì]
表面冷凝器 英文
surface conde er
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 凝 : 動詞1. （凝結） congeal; curdle; coagulate 2. （注意力集中） fix
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 表面 : surface; superficies; boundary; face; rind; sheet; skin; outside; appearance
  1. The key production technology of aluminum sheets are thickness accuracy and shape control, its main application products are drink cans 、 automobile parts, electrolytic condenser 、 small tube for condenser 、 drum for laser printer

    鋁合金板材之關鍵生產技術為提高板厚精度及形狀控制技術，應用製品主要有飲料罐、汽車零件、電解冷凝器、小斷面冷凝管、雷射印表機感光輥筒。
  2. Introduction to general ideas in air pollution control, air pollution effects, design of wall collection devices （ gravity settlers, centrifugal separators, electrostatic precipitators ）, design of dividing collection devices （ surface filters, depth filters, scrubbers for particulate control ）, design of controlling by concentration and recovery （ condensation, adsorption, absorption ）, design of controlling by oxidation （ combustion, biological oxidation, biofiltration ） and the choosing of a control technology

    本課程介紹空氣污染防制概念，空氣污染之影響，壁式集塵設備之設計（重力沉降室、離心分離器、靜電集塵器） ，分隔集塵設備之設計（表面過濾器、深層過濾器、洗滌器） ，以濃縮回收之控制設計（冷凝、吸附、吸收） ，以氧化之控制設計（燃燒、生物氧化、生物過濾） ，以及控制技術之選擇。
  3. It is concluded that it may be disadvantageous to capacity modulation at low temperature environment if the condenser area is smaller and throttle set is capillary. 3

    結果表明：系統在冷凝器面積偏小和採用毛細管作節流裝置的前提下，不利於低溫環境下的容量調節。
  4. After the rationality of theoretical model has been testified, going along a series of numerical simulation and find the best ratio of evaporation segment and condensation segment by means of analyse the temperature variety of the electronic element surface on the effect of the radiator structure change. a series of strenthen step about heat transfer put forward theoretically by means of numerical analysis focuse on the thermal resistant of each tache of the heat transfer

    在證實了本理論模型是合理的基礎上，本文根據所建立的模型進行了一系列的數值模擬計算，分析了熱管型電子器件散熱器的結構尺寸（蒸發段和冷凝段的長度比、肋片的高度等）變化對發熱器件表面溫度的影響，得到了蒸發段和冷凝段的最佳長度比。
  5. The dried material is put into the middle of shell, mixing by the rake teeth and the material shaft works back and forth. the indirect heating, equal agitation of rake teeth and grinding of breaking stick makes water in material evaporation. under the effect of vacuum system, the water in the dried material and apparent water are discharged and the vapor water is discharged from outlet of vacuum pump passing dry dust collector, wet dust collector and condenser

    被乾燥物料從殼體上方正中間加入，在不斷正反轉動的耙的攪拌下，物料軸向來回走動，與殼體內壁接觸的表面不斷更新，受到蒸汽的間接加熱，耙的均勻攪拌，粉碎棒的粉碎，使物料內的水份氣化，在真空系統的作用下，使被乾燥物料內部水份和表面水份更有利的排出，氣化的水份經乾式除塵器濕式除塵器冷凝器，從真空泵出口處放空。
  6. Steam surface condensers

    表面蒸汽冷凝器
  7. Tube surface condenser

    管式表面冷凝器
  8. And last, the experimental data are treated by using a program, and a comparison between the theoretical and the experimental results of the condensation heat transfer coefficient outside horizontal tubes with annular fins is conducted

    最後，編寫了計算程序，進行數據處理，求得管外冷凝表面傳熱系數的理論值與實驗值，對二者進行了比較，分析了誤差產生的原因，提出了冷凝器的改進方法。
  9. Brush or blow off the finned surface of the condenser monthly

    每月擦拭或. .冷凝器的翅片表面。
  10. According to the results, the cause of the error is explained, and the ways of improvement of condenser are put forward the theoretical solution of the condensation heat transfer coefficient is in excellent agreement with the experimental one

    本文所推導的冷凝表面傳熱系數的理論公式與實際情況基本相符，可應用於冷凝器的設計中。
分享友人
分享到 Line

分享到臉書