表面冷卻速度 的英文怎麼說

中文拼音 [biǎomiànlěngquèsùdù]
表面冷卻速度 英文
surface cooling rate
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 卻 : Ⅰ動詞1 （後退） step back 2 （使退卻） drive back; repulse 3 （推辭; 拒絕） decline; refuse; reje...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 表面 : surface; superficies; boundary; face; rind; sheet; skin; outside; appearance
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  1. ( 2 ) on the leading edge, the film cooling effectiveness at the zone immediately downstream of the cooling holes is affected by blowing ratio and mainstream reynolds number, while the effects are not important in the downstream zone far from the cooling holes. ( 3 ) on the front half of pressure surface, the effectiveness increases with decreasing blowing ratio at the downstream near the cooling row and it is contrary at the downstream far from the cooling row. ( 4 ) on the rear pare of the pressure surface, the effectiveness decreases with increasing blowing ratio and does not vary so much downstream in the cases of higher blowing ratio

    研究結果表明葉片吸力面端壁附近區域壓力系數分佈呈現出較強的三維特性，動葉吸力面尤其明顯；氣膜孔流量系數隨吹風比的增加而增大，在高吹風比情況下，流量系數逐漸趨于常數；在不同型面區域，冷卻效率分佈有較大的差異，而且吹風比與主流雷諾數的影響程度也不盡相同；低吹風比下，孔出口下游附近可以得到較好的冷卻，中、高吹風比下，冷氣射流在加速流動主流的作用下返回壁面進行二次冷卻，孔下游較遠區域可以得到較好的冷氣覆蓋。
  2. This segregation behavior of sn accords with the mechanism of non - equilibrium segregation. it can be obtained through the theoretical calculations that the critical time of sn non - equilibrium segregation is 124 seconds at 750 and the critical cooling rate is 8 / s when cooling from 1320. it is suggested that controlling the cooling rate during continuous casting to avoid the critical cooling rate ( 8 / s ) and avoiding high stress near the trough temperature ( 750 ) may control the form

    通過研究殘留元素sn的偏聚機制及其對o . 15wt . % c鋼熱塑性的影響，對試驗鋼進行脆性預測:建議在該鋼的連鑄過程中彎道矯直溫度盡量避開塑性谷底溫度750 ，二冷區的冷速盡量避開臨界冷卻速率8 / s ，從而可以減少該低碳鋼連鑄坯表面裂紋和橫向裂紋，提高其成材率。
  3. Ultrasonic plastic welding theory is generated by the generator 20khz or 15khz pressure, high - frequency signals, the system can be adopted for the high - frequency signals into mechanical vibrations, and in plastic products working, through working surface and internal friction among elements spread by the department of the interface temperature, when the temperature reached the melting point of her own, that the working interface rapid melting, and then fill in the gaps between the interfaces when shock stop working at a certain pressure and cooling will be a perfect welding

    的高壓高頻信號通過換能系統，把信號轉換為高頻機械振動，加於塑料製品工件上，通過工件表面及內在分子間的磨擦而使傳處到介面的溫度升高，當溫度達到此工件本身的熔點時，使工作介面迅速溶化，繼而填充于介面間的空隙，當震動停止，工件同時在一定的壓力下冷卻定形成完美的焊接.點擊數： 723錄入時間： 2006 - 5 - 14
分享友人
分享到 Line

分享到臉書