裂變損失 的英文怎麼說

中文拼音 [lièbiànsǔnshī]
裂變損失 英文
fission loss
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 裂變 : [核物理] atomic fission; fission; nuclear fission
  • 損失 : 1. （失去） lose 2. （失去的東西） loss; wastage
  1. At low concentration of zn, the changes in ultrastructure were nuclei deformation, chloroplast swelling and disorder of thylakoid arrangement ; serious damages in ultrastructure caused by greater zn stress were indicated by scattered nucleoli, condensed chromatin, almost empty nuclei with nuclear membrane disrupted and nucleoplasm flowing into cytoplasm, swollen and partly dissolved cristae of mitochondria, disrupted and collapsed chloroplast envelopes, and some dissolved thylakoids that flew into cytoplasm

    超微結構的變化也呈現加重趨勢，低濃度處理的變化為細胞核變形、葉綠體膨脹、類囊體排列紊亂；嚴重的超微結構的損傷是核仁散開、染色質凝集，細胞核幾乎成為空核和核膜破裂，核質散出；線粒體脊突膨脹和部分溶解；葉綠體膜斷裂、消失和部分類囊體溶解和散到細胞質中。
  2. Several materials with large coefficient of expansion were selected to make packaging components, and it was found that the packaging materials have good temperature sensitivity and compatibility with optical fibers. experimental accuracy and repetition of fbg temperature sensitivity and compensation were discussed. have selected several materials which has bigger coefficient of expansion to do packaging components, have made many temperature experiments, there have not flaws, such as aging, crackle, absciss layer, packaging materials have good temperature sensitivity and compatibility with optical fiber ; have designed the simple and practical packaging components, have performed a serials of experiments about accuracy and repetition of fbg wave - length, have obtained the first step conclusion ; have analyzed the result and made comparison between the result of different experiment, have summarized the best packaging effect and several rules to reduce mistskes

    本文所做的主要工作包括以下幾個內容：一、選取了常見的熱膨脹系數大的材料製作封裝元件，經過多次一80到80反復測試，封裝元件沒有出現老化開裂、封裝裂紋、空洞、離層等缺陷，封裝材料具有良好的溫敏穩定性及復用性，與光纖相容性較好；二、對光纖光柵進行簡單、實用的封裝處理，就封裝效果的優劣性、波長測量的準確度、重復性和封裝時產生的波長損失等方面進行了一系列的實驗，得出了初步的結論；三、對溫敏和溫度補償式封裝的實驗數據進行了詳細的分析和對比，從數字上對溫變過程中光纖光柵中心波長的改變及溫變曲線進行了定量的分析，在大量實驗數據分析結果的基礎上，總結出哪種材料封裝效果更好，以及如何有效的減小實驗誤差。
  3. The knowledge on the properties of used materials is urgently needed for reasonable life - prediction and life - distribution. as cylinder bolts are concerned, they often rapture at the first tooth - root resulting from lower high temperature strength of their material and higher stress. since bolts operate at high temperature environment, creep skew and damage causing their failure are important factors that can not been neglected

    就汽缸螺栓而言，由於螺栓材料的高溫強度偏低，預緊力過大，常常在螺栓的第一齒根部位發生蠕變脆性斷裂，因其長期在高溫環境下工作，蠕變變形和蠕變損傷是其失效的一個不可忽略的重要因素。
  4. With improvement of material composition and processing, the failure modes demonstrate predominately elevated wear and plastic deformation, and no earlier failure occurred, leading to a considerable improvement of service life and a stable number of 6000 ~ 7000 times, 80 % more than forging steel dies

    經改進材質及工藝后，熱磨損、塑性變形為主要失效形式，而未出現早期斷裂失效，壽命得到明顯提高，穩定在6000 ~ 7000件，高於鍛造模具鋼80 %以上。
  5. There are three modes for the invalidation of cuw / crcu integrated contact : splitting from the binding interface of cuw / crcu ; uneven distortion of contact finger and severe eroding loss

    觸頭的動態失效主要有三種方式:在結合面處發生斷裂，嚴重燒損后無法接通，觸指變形。
  6. Firstly, this paper discussed failure mechanisms, failure reasons and precautions of explosion, corrosion, abrasion, deformation and leakage etc by studying the rationales of internal and overseas failure analysis for pressure vessels. secondly, each fault tree of failure analysis was built and the knowledge base of failure analysis for pressure vessels was made by combining production rule with framework in the end

    本文借鑒國內外的壓力容器失效分析的基本原理，研究了破裂或爆破失效、腐蝕失效、磨損失效、變形失效、泄漏失效等失效機理、失效原因及預防處理措施，進而建立其各自相應的失效分析故障樹，最後通過產生式系統與框架系統相結合的知識表示方法建立了壓力容器失效分析知識庫。
  7. In this thesis, it is analyzed theoretically the steel bar layout pattern, the prestress loss, the concrete stress, and the discipline of the deformation and the fracture forming of structures of the partial prestress concrete frame beams, which is widely used in modern civil engineering

    本文從理論上分析了現代建築工程中廣為採用的部分預應力混凝土框架梁的布筋方式、預應力損失、混凝土應力、結構變形和開裂規律；導出了具有一般意義的預應力錨固損失以及梁的長期撓曲變形計算公式。
  8. If some way can monitor the inside state of the project structure ( mainly stress, strain and crackle ) real - time online, we can make the assessment to the security state of the engineering component real - time and reduce the loss of the accident remarkably

    如果能夠實時在線地監測工程結構的內部狀態（主要是應力、應變和裂紋） ，就能夠實時地對工程構件的安全狀態做出評估，可以把事故的損失減到最小。
  9. We designed five walls for simulate both sides of the top floor. proceeded to add unilateral horizontal static loading experiment to 4 pieces of prestressed small - sized concrete hollow block masonry models and 1 piece of normal concrete hollow block masonry model. crack - resistance behaviors were analyzed, and we have proceeded prestressing loss survey for 25 days, and discussed the reasons of prestressing loss

    模擬房屋頂層兩端單元設計試驗模型，進行了4片預應力砌塊砌體墻和1片對比普通墻體水平單調靜力加載試驗，並且進行了25天的預應力損失觀測，探討了預應力損失和加載過程中預應力筋應力的變化等問題，分析了預應力砌體的抗裂性能。
  10. Bj1036e2f1 light truck, developed by futian corporation, has continuously had batch cracking accidents on three shells including flywheel shell, clutch shell and gear - box shell from 1997 to 2000. the rate of the accident is about 1 %. the accident ever not only made futian corporation certain economic loss, but also greatly affected sale of this type truck and security of customers " life and estate

    福田公司開發的bj1036e2f1輕卡在1997 2000年連續發生三殼（飛輪殼、離合器殼和變速箱殼）批量破裂質量事故（約占該車型銷量的1 ） ，一度給公司造成較大的經濟損失，對該車型的市場銷售和用戶的生命及財產安全造成較大程度的影響。
分享友人
分享到 Line

分享到臉書