補焊 的英文怎麼說

中文拼音 [bǔhàn]
補焊 英文
patch weld; repair welding; repairing welding; weld
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. The crack between the coped and hole was removed by air arc and then repaired by welding.

    在修割邊和鉆孔之間的裂紋用氣弧消除，然後進行焊補。
  3. Repair welding requirement for grade 3 cast steel chain cables

    三級鑄鋼錨鏈補焊技術要求
  4. Welding terms and symbols - supplement - definitions for electric welding equipment

    焊接術語與符號.補充.電焊設備的定義
  5. Dye-penetrant and magneticparticle inspection techniques were used on the repaired and other 21 remaining original welds.

    在已修補了的和其餘21個原來的焊縫上進行了著色滲透和磁粉探傷工藝處理。
  6. It covers the requirements for approved inspectors, approved signatories and other requirements specific to consumer product inspection. specific requirements for construction products inspections are given in hkias supplementary criteria no. 2 on general construction products and supplementary criteria no. 3 on welding inspection. inspection bodies interested in obtaining accreditations for consumer products inspection may contact hkas senior accreditation officer,

    消費產品檢驗的特定規定可見于檢驗機構認可計劃《補充準則第1號》 ，當中載有核準檢驗員和核準簽署人員的規定，以及其他適用於消費產品檢驗的特定規定；至於建築產品檢驗的特定規定則可見于有關一般建築產品的檢驗機構認可計劃《補充準則第2號》 ，以及有關燒焊檢驗的檢驗機構認可計劃《補充準則第3號》 。
  7. Automatic offset function for long cable up to 100m

    具有焊線長的自動補償功能，焊接電纜可長至100米
  8. Repair welding of bolting material is not permitted

    螺栓材料的補焊是不允許的。
  9. Repair welding standard for stainless steel propeller of ships

    船用不銹鋼螺旋槳補焊技術條件
  10. Technical guide for repair welding of cast steel parts in steam turbine

    汽輪機鑄鋼件補焊技術導則
  11. The heavy mechanical general techniques and standards. repair welding for steel castings

    重型機械通用技術條件.鑄鋼件補焊
  12. Technical requirements of repair welding for defects on the 921a etc. steel plates used in naval ships

    艦艇用921a等鋼板缺陷補焊技術要求
  13. Being engaged in welding technique, including the study of repairing high temperature and high pressure cast workpieces, alloy steel parts, big axle parts and so on

    主要從事焊接技術咨詢，其中包括對大型高溫高壓鑄件，耐熱鋼零部件；及大型軸類零件的補焊修復的咨詢及研究。
  14. This paper analyzes the repairing feature on perforating casing and presents a new procedure that the root of perforating hole is covered by a little block age plate and then repair welding is carried out

    通過對射孔槍管修復特點的分析，提出了先利用小堵板蓋住射孔眼的根部，再進行補焊的新工藝，實現了槍管的重復利用，為油田同類產品的修復提供了寶貴經驗。
  15. At present, the means for repairing hydraulic turbine blades in our country are still manual weld and manual polish. the working condition is bad and labour intensity great for workers and overhaul efficiency low and inferior

    目前，國內水輪機轉輪葉片修復仍採用手工補焊、人工打磨等檢修手段，工人勞動環境惡劣，勞動強度大，且檢修效率低，質量差。
  16. Cavitations in foreign hydraulic turbines appear in clear water condition, so its destructive extent is not far more serious than in yellow river in our country. stronger stiffness and more agility are required for special - purpose robot for hydraulic turbine repair used in our country, especially robot for polishing after weld. foreign robot for hydraulic turbine repair could not satisfy our working require, so we develop special - purpose robot system that is used to polish and weld repair cavitated flow path surfaces of hydraulic turbines on all locations

    國外水電站的水輪機汽蝕是在清水條件下產生的，其破壞程度遠不及我國黃河等水域嚴重，用於我國水輪機修復工作的專用機器人，特別是補焊后承擔打磨的機器人，要求有更強的剛度和更大的靈活性，國外水輪機修復機器人滿足不了我國水輪機修復工作要求，因此我們開發了用於在機坑內對水輪機空蝕磨損破壞表面進行修復的「水輪機修復專用機器人」 。
  17. Process and inspection of repair welding for aluminium alloy castings

    鋁合金鑄件補焊工藝及檢驗
  18. Process and inspection of repair welding for investment castings of stssl

    熔模鑄造鋼鑄件補焊工藝及檢驗
  19. Overlaying - welding research and property analysis of fiction - stir - welding

    攪拌摩擦焊缺陷補焊工藝及性能分析
  20. This paper introduces the urea synthesis tower replacement titanium lining repair methods and processes, focusing on titanium lined with grass - roots repair welding, the new titanium lined tiejin, welding, and other aspects of the control of the same industry titanium lining equipment repair summary an effective set of methods

    本文介紹了尿素合成塔鈦襯里更換修理的方法及過程，重點闡述了鈦襯里的切除、基層的補焊、新鈦襯里的貼緊、焊接等方面的控制，對同行業鈦襯里設備的修復總結了一套行之有效的方法。
分享友人
分享到 Line

分享到臉書