裝模螺栓 的英文怎麼說
中文拼音 [zhuāngmóluóshuān]
裝模螺栓
英文
clamping screw- 裝 : Ⅰ名詞1 (服裝) dress; outfit; attire; clothing 2 (演員的化裝品) stage makeup and costume Ⅱ動詞...
- 模 : 模名詞1. (模子) mould; pattern; matrix 2. (姓氏) a surname
- 螺 : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
- 栓 : 名詞1. (可開關的機件) bolt; plug 2. (塞子) stopper; cork
- 螺栓 : bolt; screw bolt; threaded bolt
-
The modularized and interchangeable accessories reduce not only the variety of accessory, but also the trouble of user, because the same accessory can be applied to mccb with different rated current and the installation can be implemented without bolt just by the particular connective manner. easy range launched by schneider - electric enriched the family of merlin gerin, brought the customers much more variety of choices, consolidated the leader s position of merlin gerin in the area of electric solutions
附件的模塊化設計減少了附件的種類,而通用性則大大減少了使用者的煩惱,同一種附件可適用於多種不同電流規格的塑殼斷路器,電氣附件獨特的卡接安裝方式可以使附件在不需用螺栓連接的情況下可實現快速的裝配。Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block
在上模節流棒槽內裝入節流棒,將節流棒調節螺栓裝配進節流棒的螺絲孔中,再裝配上壓塊。The anchor bolts and nuts must be processed and used as a whole set. the embedded anchor bolts for equipment foundation shall be installed and fixed with positioning forms
地腳螺栓與螺母必須配套加工,配合使用。設備基礎的預埋地腳螺栓採用定位模板安裝固定。On the basis of the finite element analysis of the press - mounting machine, to solve the modeling error of the previous modeling method, a new mixed - model method using the spring element and thin - layer solid element was introduced in this thesis. an experiment designed to test the interface static stiffness was carried out and the needed modeling datum was obtained
在對壓裝機進行了整體建模模擬的基礎上,針對壓裝機整體建模存在的誤差問題,本文提出了一種改進的彈簧單元和薄層實體單元混合建模的方法,並依此設計了螺栓結合面靜剛度測試試驗,通過試驗獲得了建模所需的參數。Form ties bolt bore : bore drilling should be done when first time used form plate assembling on site to keep away from steel bar and reduce blank out bore happened
7對拉螺栓孔:第一次使用的模板應在現場組裝就位時鉆孔,以避開鋼筋,減少廢孔的出現。In view of the high demand on the coaxial tolerance of linear induction accelerator in centering assembling and considering the interaction among flange, bolts and gasket, finite element analysis was adopted and a 3 - d finite element model of accelerator in centering assembling with bolted - flange connection was built
摘要針對直線感應加速器對中裝配同軸度要求高的特點,考慮法蘭、螺栓和密封墊相互作用,建立了加速器對中裝配法蘭螺栓聯接的三維有限元模型,分析了螺栓預緊力對加速器對中裝配時同軸度的影響作用。Engineering drawing system can draw two dimension curve graphs, main detail drawing and assembly drawing. the curve of internal trajectory and dynamic simulation of particle external trajectory. the detail drawing includes the graph of chamber, grain design, connection body, nozzle, some standard part
工程繪圖可以繪制二維曲線圖和零部件圖,其中二維曲線包括有內彈道壓(推)力?時間曲線、質點外彈道動態模擬曲線;零部件圖包括有標準螺栓與螺紋孔、燃燒室結構圖、裝藥設計截面圖、連接底結構圖、噴管結構圖及火箭發動機總體裝配圖。Wall form installation please see attached sketch no. - 4. expended cement mortar shall be used for sealing after form dismantled and pull bolts removed
墻板模板安裝見附圖4 。在模板拆除對拉螺栓拿出后,採用微膨脹水泥砂漿封堵。After ascertaining the motion projection, the engine model with double connecting rods and crankshafts is established and the rationality about the structure of the model has been tested. at the same time, the standard component parts library such as bolt, nut, bond and pin is builded, which will be convenient to later design
確定運動機構方案后,在分析裝配模型,裝配關系等基礎上用solidworks建立了零件庫和螺栓、螺母、鍵、銷等標準件庫,根據內燃機結構特點實現新型雙連桿雙曲軸內燃機的裝配模型,並檢查了整個樣機模型設計的合理性。分享友人