襯層 的英文怎麼說
中文拼音 [chèncéng]
襯層
英文
cushion-
Friction pulley linings for winches and winders in mining
礦井提升機和卷揚機用摩擦輪襯層Ductile iron pipes - centrifugal cement mortar lining - composition controls of freshly applied mortar
球墨鑄鐵管水泥砂漿離心法襯層新拌砂漿的成份檢驗Interface debond between propellant and liner is a key form of failure of the structure integrity in the analysis of solid rocket motor
在固體火箭發動機結構完整性分析中,襯層/推進劑藥柱粘接界面的脫粘是完整性被破壞的關鍵形式之一。Because the propellant grain is viscoelastic material, the liner and adiabatic layer are also viscoelastic one, the interface debond problem is actually interface crack about elastic - viscoelastic or bi - viscoelastic materials. research about this problem relates to the knowledge of viscoelastic mechanics and interface fracture and combustion. numerical analysis method about interface debond on solid rocket motor is researched in this paper
由於固體火箭發動機的推進劑藥柱是一種粘彈性材料,襯層和絕熱層也具有粘彈性性質,因此其界面脫粘問題實際上是彈性-粘彈性或雙粘彈性各向同性材料界面裂紋問題,對該問題的研究涉及到粘彈性力學、界面斷裂力學和燃燒學等相關學科。Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
採用氟塑料f4整體冷壓成型及熱熔加工等先進技術製造,使內襯層無縫搭接且與外層金屬管壁緊密粘接,在允許工作狀態下能夠保持同步變形,從而提高了襯里層在相對高溫高真空度的工況下的使用壽命,杜絕了一般襯氟管在冷熱交替,及負壓的條件下使用易產生襯塑層鼓癟阻塞流道及塑料拉裂的問題,是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。Ductile iron pipes - centrifugal cement mortar lining - general requirements
球墨鑄鐵管水泥砂漿離心法襯層一般要求Plastics piping systems for renovation of underground non - pressure drainage and sewerage network - part 3 : lining with close - fit pipes
地下非壓力排水和排污管網更新用塑料管道系統.第3部分:緊配合管用襯層Glass lined apparatus and pipe equipment ; thermal shock resistance
玻璃襯層裝置和管道設備.耐熱沖擊性能Glass lined apparatus and pipe equipment ; chemical enamel ; quality requirements and specification
玻璃襯層裝置和管道設備.化學塗釉.質量要求和規范Increasing the thickness of lining material and selecting corrosion - resistant adhesives made the painting layer be used for three years
通過增加防腐蝕襯層厚度、合理選擇粘結劑,使防腐蝕層使用壽命達到3年。In - situ concrete lining
現場澆築混凝土襯層In situ concrete lining
現澆混凝土襯層Research and design of connecting move control system for tyre underlayer product line
輪胎內襯層生產線連動控制系統的實現Steel plate lining
鋼板襯層Pvc - p. plasticized polyvinyl chloride roofing felt with non - woven roving inner layer ; requirements
帶非編織的粗紗內襯層的增塑聚氯乙烯This machine is willing to have a high production ability, the gum anticipates temperature low, the electric power consumes little, quality good, the petrochemistry even etc. characteristics, so used for the gum tube, inner tire broadly, tape inner pad layer, seal completely, electric wire, electric cable, protect the ware extrusion of a set of etc. rubber to prepare to take shape
用途介紹:本機具有生產能力高,膠料溫度低,電能消耗少,混合質量好,塑化均勻等特點,因此廣泛地用於膠管,內胎,膠帶內襯層,密封條,電線,電纜,護套等橡膠製品擠出預成形。Leak detection systems - part 7 : general requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets
檢漏系統.第7部分:填隙部位防漏襯層和防漏套的一般要求和試驗方法Aerospace series ; rod ends, adjustable, self - aligning plain bearing with self - lubricating liner and threaded shank ; dimensions and loads
航空航天系列.紋螺桿的自潤滑襯層的自校準關節軸承的The influence of metallic mesh packing block on radar wave shielding is only dependent on packing block material ’ s surface electric resistance, independent on other factors of material. the less surface electric resistance is, the better metallic mesh ’ s shielding effect is
而且金屬網柵襯層對雷達波屏蔽作用的影響只與襯層材料的面電阻有關,與材料其它因素無關,面電阻越小,網柵的屏蔽效果越好。After studying the precision of fdm process, a rapid edm electrode fabrication technology based on fdm is developed, the technology, which combined pulse - reverse electroforming with strengthening of copper wire - arc spraying, can obtained compact crystal electrode ' s working part, and strengthened filling part which has big adhesion strength, better electricity and heat conductivity, the edm performance of the obtained electrode reaches that of electrolysis copper electrode
繼fdm工藝精度研究后,開展了快速模具製造技術的研究,建立了基於fdm原型快速製造電加工電極的工藝。該工藝將脈沖電鑄和電弧噴塗紫銅背襯相結合,獲得了結晶緻密的電極工作層和結合強度高、導電與導熱性良好的電極背襯層,得到的電極達到了常規機加工紫銅電極的電加工性能。分享友人