角位移 的英文怎麼說

中文拼音 [jiǎowèi]
角位移 英文
angular displacement; angular rotation角位移測量 angle displacement measurement
  • : 角Ⅰ名詞1 (牛、羊、 鹿等頭上長出的堅硬的東西) horn 2 (古時軍中吹的樂器) bugle; horn 3 (形狀像...
  • : Ⅰ名詞1 (所在或所佔的地方) place; location 2 (職位; 地位) position; post; status 3 (特指皇帝...
  • : Ⅰ動詞1. (移動) move; remove; shift 2. (改變; 變動) change; alter Ⅱ名詞(姓氏) a surname
  1. The radome causes an angular displacement of the tracking aerial polar diagram.

    天線罩使跟蹤天線的極圖產生了角位移
  2. This requires a servo follow-up system to keep the operating angular displacement between gimbal and case down to acceptable low limits.

    這就需要有一隨動系統使框架與殼體間的工作角位移保持在滿意的小范圍之內。
  3. Information sensing is provided by transducers which detect relative angular displacements between the gyro gimbal and the supporting case.

    信號的敏感是由能探測陀螺框架和支撐結構間的相對角位移的傳感器來提供的。
  4. Owing to its excellent adaptability to large angle - displacement between two transmission shafts and other characteristics such as large transmission ratio, terse mechanism, high transmission efficiency, cardan cross - pin spindles has been widely used as an important mechanical part in transport machines, metallurgy machines, petrolic machines, heavy machines, etc. as an effective and promising approach to resolve complicated development of modern software, component - based development ( cbd ) is put forward to change the present way of software development by producing software through assembling ready software components and its final target is to realize the industrialization of software development totally

    十字軸式萬向聯軸器能夠很好地適應傳動軸間的較大角位移,而且具有傳遞扭矩范圍大、結構緊湊、傳動效率高、維修保養方便等特點,是一種重要的傳動部件,因此在交通運輸、冶金、重型機械等領域中得到廣泛應用。基於組件的開發是近幾年發展並日益成熟起來的一種軟體開發新方法,其核心思想是以流水線方式、通過組裝組件生產軟體,從而容易實現軟體開發的工業化。
  5. Electronic comparators. angular dimensional sensors. technical data sheet

    電子比較儀.角位移傳感器.技術數據表
  6. Slope - deflection equation with a type of non - ideal constraints at end of beam

    一類非理想桿端約束下的轉角位移方程
  7. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時,採用考慮翹曲作用的曲線格子梁分析方法,應用矩陣法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析,考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致,引入支座節點坐標矩陣,使得梁端的未知量與斜支座約束方向一致,來計算單元剛度矩陣和單元節點力,然後按照矩陣法組集總剛並建立結構剛度方程,根據結構剛度方程即可求解未知的節點及桿端力,推導出任意截面處的內力計算公式。
  8. It appears that both rate and displacement controls are acceptable to pilots.

    看來速度操縱和角位移操縱都是駕駛員可接受的。
  9. Grating angular displacement measuring system

    光柵角位移測量系統
  10. Rules for the inspection of raster angular displacement sensor for export

    出口光柵角位移傳感器檢驗規程
  11. Verification regulation of angular displacement transmission chain error tester

    角位移傳動鏈誤差檢查儀檢定規程
  12. Angle displacement measurement

    角位移測量
  13. Angular displacement grationg

    角位移光柵
  14. Angular displacement measuring systems with absolute and incremental encoders ; concepts, requirements, testing

    帶絕對編碼器和增量編碼器的角位移測量系統.概念要
  15. In this paper, the study for the two - phase hybrid stepper motor as a position sensor is investigated

    針對二相混合式步進電機固有的特點,對其作為連續角位移測量傳感器進行了深入的研究。
  16. In chapter 2, the mathematical model of two - phase hybrid stepper motor as a generator is established. then according to the model, the functional relationship is obtained between the terminal voltage of stator winding and continuous rotor position

    第二章,建立了二相混合式步進電機的發電模型,並進一步簡化得到定子繞組端電壓與轉子轉之間的函數關系式,為步進電機實現連續角位移測量的研究奠定理論基礎。
  17. The main controller is in charge of managing, communicating and the measuring of grating - displacement and angle - displacement. the subcontrollcr is in charge of the measuring of inner diameter of psd, the analog - to - digital converting of the serial a / d and the data processing of dsp

    主控制器完成管理、通信及光柵角位移測量控制功能;子控制器完成psd內徑尺寸檢測、串列a / d模數轉換及數字信號處理器( dsp )數據處理功能。
  18. It establishes the foundation for the continuous rotor position detection. in chapter 3, according to the model, two - phase hybrid stepper motor as a position sensor is designed. it is implemented in an environment composed of matlab, simulink and real - time workshop

    第三章,根據二相混合式步進電機的發電模型,利用matlab simulink模擬軟體及其信號採集硬體系統,對步進電機實浙江工業大學碩士學論文現連續角位移測量傳感器進行了設計。
  19. Vibration of tank gun in the process of firing is one of the main factors that affect its firing accuracy, especially the instantaneous angular motion and the instantaneous linear velocity at the point of gun muzzle when the projectile leaves the barrel bore

    影響坦克炮射擊精度的主要因素之一是火炮振動,起關鍵作用的振動分量是在彈丸出炮口瞬間炮口振動角位移和橫向線速度。
  20. In the simulation it was found that there was interference when the manipulator moved. it is because the manipulator is controlled by minimum time method. the method has no constraints about angle displacement

    經分析后發現主要是由於採用的控制方法是最小時間控制,造成了機械手各關節的角位移太大,從而產生了干涉。
分享友人