角度測量法 的英文怎麼說

中文拼音 [jiǎodùcèliángfǎ]
角度測量法 英文
angular measurement
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 角度 : 1. [數學] （角的大小） angle; the degree [size] of angle 2. （看事情的出發點） point of view; angle
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  1. Research on modeling method for laser auto - collimation angle measurement system

    激光自準直角度測量系統建模方法研究
  2. Reciprocating internal combustion engines. handle starting equipment. part 2 : method of testing the angle of disengagement

    內燃機.手柄起動裝置.第2部分:測量脫扣距離和角度的方法
  3. Based on the model of resource survey spaceborne laser altimeter, the noncooperative regulable attenuation module, including angular measure setting, beam splitter, energy meter, attenuator and simulant target, was designed and founded

    結合激光高度計原理樣機，設計並建立了非合作目標可調衰減法模塊，該模塊包括角度測量裝置、分束片、能量計、衰減器以及模擬目標物。
  4. The glint suppression using high resolution range profile under conical angle measurement is studied, the angle information in signal components of scatters are extracted and averaged to suppress the glint. nonlinear kalman filtering methods under near spherical coordinate are analyzed and used to get more accurate tracking

    研究了圓錐掃描測角體制下基於距離高分辨的角閃爍抑制方法，利用距離維高分辨像，提取強散射中心反射信號分量，在此基礎上估計出各個強散射中心的角度測量值，採用平均方法減少角閃爍對測角的影響。
  5. Method of measurement of centre beam intensity and beam angle of reflector lamps

    反光燈的中心波束強度及波束張角的測量方法
  6. Backed up by the soplat theory based on particle kinematics, the second chapter of this paper presents with analysis and simulation of several single observer passive measurement models, which uses such relative movement parameters as bearings changing rates and centrifugal acceleration information on the basis of bearings measurements. in the third chapter, the observability of location respectively using bearings and its changing rates information and centrifugal acceleration information is analyzed, and its observable condition is got. the fourth chapter puts forward the modified covariance extended kalman filtering ( mvekf ) against the defect of traditional extended kalman filtering ( ekf ), whose performance is simultaneously compared in the chapter with the performance of ususal tracking algorithm such as ekf, mgekf, iekf by computer simulation

    在近年來提出的基於質點運動學原理的單站無源定位理論基礎上，本文第二章提出了幾種在角度測量的基礎上增加角度變化率及相對運動的離心加速度等運動學參數的單站無源測量模型，並對它們進行了分析和模擬；第三章分別對利用角度及其變化率信息定位和利用離心加速度信息定位的可觀測性進行分析並得到了相應的可觀測條件；第四章針對傳統擴展卡爾曼（ ekf ）方法的缺點，提出了一種修正協方差的擴展卡爾曼濾波（ mvefk ）方法，並將其和ekf 、 mgekf 、 iekf等常用的單站無源定位濾波方法進行了性能模擬比較；第五章通過引入雷達機動目標跟蹤方法和模型，提出了利用角度及其變化率對機動輻射源跟蹤的多級噪聲自適應方法和imm方法；第六章主要對角度變化率和離心加速度參數的獲取技術進行了研究，提出了幾種高精度測量脈沖序列多普勒頻率變化率的方法。
  7. Standard test method for corona - treated polymer films using water contact angle measurements

    用水觸點角度測量法測定電暈處理聚合物薄膜的標準試驗方法
  8. Then, this paper presents an improved t measuring speed method basing on t measuring speed method, and simultaneously realizes speed and angle measuring with two quadrature encoder pulse circuits of tms320lf2407a. the measuring speed formula is amended based on measuring speed error analysis

    其次，在t法測速的基礎上提出了一種改進的t法測速法，並利用tms320lf2407a的兩組正交編碼電路同時實現速度與角度測量，在分析測速誤差的基礎上，對測速公式進行修正。
  9. The method of gluing long grating to fan - shaped wheel resolved the problem of measuring of angle

    將長光柵貼在扇形輪上的辦法來解決角度測量的問題，對測量系統進行空間定位。
  10. To satisfy the experiment request, the equipment generating magnetic field and the angular instrument are improved. for light wave from semiconductor laser is infrared wave in the experiment, the calibrating measurement utilizing visible light from he - ne laser is used. firstly the light path is adjusted using visible light roughly

    在搭建系統時，根據實驗要求對磁場儀（小磁場時的穩定性）及摘要第2頁測角儀（測量精度）進行了改進；在調整光路時， （又據使用的紅外激光光源的特點，採用了先利用he ne激光器的可見光波粗略校準光路，然後換用半導體激光器精確校準光路的方法。
  11. On the base of the relativity and the data self - sealing characteristics of circular division measurement, an arbitrary measurement system on circular division and dihedral is built, and the processing method of the dynamic data zero average and the balancing based on self - sealing nature reference are also built

    在圓分度測量的相對性和數據自封閉特徵的基礎上，建立了基於圓分度和二面角測量的任意角測量系統，和基於自封閉自然基準的動態誤差數據零均值處理和平差處理方法。
  12. The surface deformation monitoring of the side - wall by combination of the forward intersection method with the analytical trigonometric elevation measurement demonstrates that the plane deformation and vertical deformation of the side - wall are small, and the quality of dam filling and side - wall construction is satisfactory

    用能夠滿足精度要求的前方交會法與解析三角高程測量法結合的方法對邊墻表面變形進行監測，結果表明，邊墻平面位移和垂直位移均較小，大壩填築和邊墻施工質量可靠。
  13. The author discusses the basic category of land sustainable use and construct theoretical foundation for demonstration and policy application by summarizing and inducing the private achievements. under the leading of the theories system, the author investigates systematically natural and economic conditions, the characteristic and the present condition of land resource use and discovers the problem and result of landuse in the county. at the same time, the writer forecasts the demand of some kinds of landuse by analyzing the conductive and exploiting potential from nature, economy and society

    研究的總體思路是：總結、歸納已有研究成果，探討土地資源可持續利用的基本范疇，構建實證研究和政策運用的理論基礎；在理論體系的指導下，系統考察該縣土地資源開發利用的自然及社會經濟條件、土地資源特徵、利用現狀，揭示該縣土地利用存在的問題及其後果；從自然、經濟、社會三個方面系統分析了各種土地利用類型的生產、開發潛力，並對多種土地利用類型做了用地需求量預測；進一步深入剖析了影響土地資源可持續利用的因素指標，從而建立了指標體系；在此基礎上，採用綜合指數法和單指標多角度評價法就酉陽土地資源的可持續利用作以評價；最後，提出酉陽土地資源可持續利用的戰略構想和切實可行的對策、建議。
  14. Firstly, optical trigonometry measurement principle and wok principle of linear ccd are introduced, which are based on to design optical focusing and imagery system with he - ne laser instrument as illuminant. secondly, peripheral circuit of linear ccd is designed in theory and experiment. finally non - contact thickness measurement instrument is constructed, using ccd as photoelectric transformation element and microprocessor as the controller

    本文首先介紹了光學三角法測量原理，並對線陣ccd的工作原理進行了研究，以此為基礎採用氦氖激光器為光源，設計了光學聚焦及成像系統，對線陣ccd外圍電路的設計進行了理論設計和實驗研究，最後設計了以ccd為光電轉換元件，以微處理器為控制核心的非接觸式厚度測量儀及其系統。
  15. Chapter four is focused on this and it gives us a very detailed introduction to the calibrating idea and algorithm realizations. it also introduces the calibrating performances by using three different off - line calibrating algorithms along with the simulation results

    文章第四章針對離線校正的思路與演算法作了詳細地介紹，比較了三種離線校正演算法在不同的誤差模型與噪聲模型中對和差接收通道校正後角度測量精度變化的情況。
  16. The main idea of this research can be summed up as following words, reflecting light or scattering light upon the surface of measured object formats an image on the photo surface of psd by a optical system, because of the good relationship between the offset of image point in psd and the offset of object thickness, a mathematical model can be founded according to this relationship. it can measure the shift of object thickness through these analyses of movement of image point position in psd, and this device can be tested its reliability with many practical specimens

    光學式非接觸厚度-微位移測量儀是在激光三角測量法的基礎上實現的，在本研究方案中，根據象點在psd上的移動量建立與被測物厚度-微位移變化之間的數學模型，通過對象點位置變化的計算，實現被測物厚度-微位移變化量的測量。本文重點闡述了光學式非接觸厚度-微位移測量儀的工作原理，並對測量儀的工作過程進行了分析；對影響測量精度的因素做了討論。
  17. The system to the original software systems have done a lot of improvements, and further perfect the original measurement system functions, and increase the border extraction algorithms, manual measurements, dimension detection, and measurement of large dimension measurement, solutions to the single measuring issue, makes it as a common set of dimension measuring systems

    本系統對原軟體系統做了大量的改進，進一步完善了原系統的測量功能，設計了邊界提取演算法、手動測量、尺寸檢測、角度測量及超屏幕尺寸測量方法，解決了測量方式單一的問題，使其成為一套通用的檢測系統。
  18. In this paper, in order to estimate coal storage volume in open stockyard, we have analyzed the optical triangulation and applied it to the measurement of large surface we have stated the measuring theory of distance with laser and the measuring theory of angle. we have also analyzed main factors influencing measurement precision and studied several key techniques in large - scale measuring such as the problem of non uniformly distributed of distance measuring resolution in large surface measurement, the methods of locating laser spot center and so on

    本文通過對火力發電廠露天煤場存煤量的自動檢測系統的研究，深入分析了光學三角測量方法的原理，並將其應用於大型曲面測量；闡述了激光測距原理和角度測量原理；對大型曲面測量的實現方法、畸變光斑圖像的幾何中心的準確定位等幾個方面的關鍵技術進行了探討；分析了大范圍測量時影響測量精度的主要因素。
  19. Having obtained an initial position with a least - square method, a more precise result can be worked out from information contained in the bearing measurements

    在利用最小二乘法獲得定位初值后，根據每次角度測量的信息進行目標位置估計。
  20. The angle - encoder principle and design are introduced, mathematics - logical method of angle measurement circuit are introduced

    摘要文章簡要介紹了編碼器的工作原理，給出了角度測量電路的一種設計方式及信號的運算處理方法。
分享友人
分享到 Line

分享到臉書