角樹材 的英文怎麼說
中文拼音 [jiǎoshùcái]
角樹材
英文
hornbeam-
Both the complicatedness varieties trees, the thick liquid material that the material differs greatly and the remaining leftover bits after wood processing, wood shaving, sawdust, sub thick liquid, cotton stalk, hemp stalk, bush, crudefiber crop, rice wheatgrass, reed, crudefiber crop, many kinds of goods thick liquid board, wasted paper, bagasse, agrimony etc. canbe fasten separated into the good fibre with higher velocity and proper to rub a block of interval
高濃磨對漿料的適用范圍較廣，無論是樹種復雜，材料差異較大的漿料，還是木材加工后剩餘的邊角料，以及蝕花、鋸屑、節子漿、棉稈、麻稈、灌木、枝椏材、稻麥草、芳菲、麻類多種商品漿板、廢紙、甘蔗渣、龍須草等，都能夠以其料高的旋線速成度及適當磨片間隙分離成優質纖維。West indian locust tree having pinnate leaves and panicles of large white or purplish flowers ; yields very hard tough wood
西印度群島的一種角豆樹，有羽狀的葉片和開白色或紫色大花的圓錐花序， ；木材十分強韌。Construction, beams and furniture. allergy sometimes caused by fine dust on sawing, and resin easily stuck to saw - teech
建築用材?梁?車只角材?合板用旋切單板?鋸屑易使皮膚過敏?木材中所含樹脂常黏滯在鋸齒中。Based on the technical parameters, quality matter and character of polymeric materials and its products, the statistical method such as orthogonal array design, pareto diagram, histogram, significance testing, fuzzy mathematics have been used to carry out a series of study. by doing so, the inherence relationship and variance property, degree and reason of polymeric materials and its products have been obtained ; it could get better improved by adopting correcting measure
本論文以高分子材料及其製件的工藝參數、質量問題和質量特徵值為研究對象，利用正交實驗設計、調查表、因果圖、排列圖、直方圖、控制圖、故障樹（ fta ） 、顯著性檢驗、相關分析以及模糊數學評定法等多種統計技術方法，從不同角度進行了一系列探索性研究，得到了高分子材料及其製件內在關系及變異的性質、程度和原因，採取了糾正措施並取得了較好的效果。Aerospace series. honeycomb materials with tubular cells, hexagonal, fibre glass, polymimide resin impregnated, oriented at plus over minus 45 degrees. product standard
航空航天系列.正負45度取向聚酰亞胺樹脂浸漬的玻璃纖維六角形管狀蜂窩的蜂窩材料，正負45度取向.產品標準Insulating materials - industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross - section based on thermosetting resins for electrical purposes - definitions, designations and general requirements
絕緣材料.基於熱固樹脂材料的矩形和六角形截面的工業用剛性模塑的疊層管材和棒材.定義符號和名及一般要求Insulating materials - industrial, rigid moulded, laminated tubes and rods of rectangular and hexagonal cross - section based on thermosetting resins for electrical purposes - part 2 : methods of test
絕緣材料.電工用工業剛性模製矩形和六角形橫截面的熱固性樹脂基層壓管材和棒材.第2部分:試驗方法Insulating materials - industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross - section based on thermosetting resins for electrical purposes - part 1 : definitions, designations and general requirements
電氣用基於熱固樹脂的工業硬質模製扁形和六角形層壓管材和棒材.第1部分:定義標識和一般要求The engineering constants around the stitch hole in the composite laminate are analyzed using the fdm. it is found that the elastic constants have distinct region character and the traces of the resin - rich pocket in different lamina are clear
採用纖維彎曲模型分析了縫紉復合材料單層在縫紉孔附近的最大纖維偏轉角、縫紉影響區以及縫紉復合材料單層及層合板工程常數的變化，發現工程常數具有很明顯的區域性，能夠看出各層中樹脂富集區的痕跡。分享友人