觸發耦合方法 的英文怎麼說

中文拼音 [chùfāǒugěfāngfǎ]
觸發耦合方法 英文
trigger-coupling method
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 發 : 名詞（頭發） hair
  • 耦 : Ⅰ動詞[書面語] （兩人並耕） plough side by sideⅡ名詞1 （古農具名） plough2 [書面語] （兩人一組） a...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 觸發 : detonate by contact; touch off; trigger; strike
  • 耦合 : [物理學] coupling; interconnection; catena; linkage; linking
  • 方法 : method; means; way; technique; process; procedure; plan; device; recipe; fashion; tool; maneuver
  1. According to the test conditions, the double polarity inputting mode is adopted in the circuit of voltage - frequency converting part ; storage batteries are used in the optical emission part of optical fibre isolating and transmitting device, that can guarantee isolation between the main circuit and the testing system ; the 89c51 singlechip is used in the singlechip testing - controlling unit, the peripheral circuits are extended, data are transmitted through the serial port in this part ; the p opular software delphi5. 0 is used in the pc part, the communication between singlechip and pc by serial port, plotting of current wave, regulation of data ; the optical - electrical isolating and triggering are used in the controlling part, this can guarantee the veracity and reliability of breakers triggered, this triggering mode is also used in the triggering of the main closing breaker, the tested breaker and the assistant breaker, the triggering signals are sent out by a singlechip

    壓頻轉換部分電路中根據實際情況採用了雙極性輸入方式；光纖隔離傳輸裝置的光發射部分電源採用了蓄電池供電，確保了主迴路與測試迴路的完全隔離；單片機測控部分採用了89c51單片機，擴充了外圍電路，通過串口向pc機傳送數據； pc機與單片機之間的串口通訊、波形繪制、數據管理等都採用了軟體delphi5 . 0編寫。該測試系統中預留了輸出口，可以對合成迴路中的主合閘開關、被試開關、輔助開關進行觸發，信號由單片機發出，控制部分採用了光電耦合隔離觸發的方法。軟體設計主要集中在對電流信號的數據採集、數據處理、數據傳送、人機界面、波形繪制和數據管理，軟體部分又可分為單片機和pc機程序設計兩大部分。
  2. Circuit design is the basis of design of demultiplexer. speed, power and chip area are the main factors that should be considered in circuit design. every circuit structure has its merits and drawbacks, e. g. cmos logic family has a slower speed, but lower power, smaller area, scfl ( source couple fet logic ) family has a higher speed, but higher power, larger area. we should choose a proper circuit structure or their mixed structure for certain design to get a good tradeoff among the three factors. flip - flop is the fundamental element of demultiplexer, setup time and hold up time are key factors, which influence the speed of circuit, thus the design aim is how to reduce them. in this thesis we place emphasis on the design of scfl latches

    速度、功耗、面積是電路設計要考慮的主要因素，不同的電路形式具有不同的優缺點，如cmos互補邏輯電路功耗低，面積小，速度相對較慢； scfl （源極耦合fet邏輯）電路速度高，功耗和面積較大。所以要針對具體設計需要選用適當的電路形式或其組合結構，以滿足設計要求。觸發器是分接器的基本組成單元，建立時間和保持時間是影響電路速度的關鍵，所以減小建立時間和保持時間是觸發器設計的主要目標，本文著重介紹了scfl鎖存器的設計和優化方法。
  3. Based on the analysis, we gave an example to study the dynamic contact with friction of the intermittent joint, and got some essential rules : the friction coefficient could n ' t influence the distributing of dynamic stress on the contact surface, and the roading rates affected evidently on the dynamic characteristic on the contact surface. in the last part, this paper made respectively use of the time - history method and the response spectrum method to analyze the dynamic response of the rock slope on baise hydraulic power plant, and got the coincident resultant. simultaneously, the contact theory was applied to study the stability of the intermittent joints

    基於上述的接觸理論和接觸分析結果，本文在最後一部分中分別利用動力時程法和反應譜法對百色水電站尾水渠的巖質邊坡進行動力響應分析，兩者計算方法得出比較一致的結果，同時採用動力摩擦接觸理論重點分析了斷層對于邊坡的穩定影響，認為斷層的存在會使得巖坡的穩定性降低，在地震等動力荷載的作用下對于斷層將發生張開、閉合和錯動現象，尤其是動力荷載和其他荷載如滲流力等的耦合作用將會對斷層產生極為不利的後果，進而影響巖坡的整體動力穩定，應該要引起足夠的重視。
分享友人
分享到 Line

分享到臉書