計數型頻率計 的英文怎麼說
中文拼音 [jìshǔxíngbīnlǜjì]
計數型頻率計
英文
counting-type frequency meter-
In digital relay, the percentage of noise will increase rapidly with the increase of sampling rate when derivation calculus is substituted by sampled difference term. to solve this problem, a new method using fragment function integrated with the least square algorithm is proposed in this paper. the influence of white noise is greatly reduced and the accuracy of the dead angle calculation is nicely improved after adopting the new method
在數字式保護中，如果用差分代替求導將導致噪聲的百分比誤差隨著采樣頻率的提高而劇增，本文對此進行了分析並提出了用分段樣條函數最小二乘法來計算電流波形的導數值，以便在提高采樣率的同時降低噪聲誤差的影響，並將其應用於基於32位浮點dsp的新型變壓器保護裝置。By making some assumptions, collision frequency were presented. then the the flocculation kinetics model was established through population balance equation. comparison of experimental data and modeling results indicate that there are the same trend between the two. so the model can predict floes number and size during flocculation of yellow river ' s loess particles without using empirical parameters. the tem and sem were used to obsever floes in the study of floe structure. the flocculation was divided as flocculi, floc and floe aggregate. the floes structure model was established by assumption that particles position in floe accords with tetrahedron. the fractal dimension of model and experimental floes was found to be coincidentso the model can reflect the structure of flocs formed in flocculation of yellow river ' s loess particles by macromolecule flocculant at a certain extent
最後，本文還對絮凝動力學和絮體結構進行了研究，在前人研究的基礎上，針對高分子絮凝黃河泥沙，對絮凝過程作了一些符合試驗條件的假設，建立了顆粒碰撞頻率表達式，應用了顆粒數量平衡方程，從而建立了絮凝過程的動力學生長模型，模型計算結果與試驗數據對比表明，二者趨勢一致，在沒有使用經驗參數的情況下基本上能夠描述黃河泥沙絮凝過程中絮體數量和尺寸分佈的變化過程；對絮體結構的研究中，應用掃描電子顯微鏡和透射電子顯微鏡對絮體進行了觀察，將絮體分為絮粒、絮團和絮網三個不同的生長階段，通過假設顆粒結合位置符西安建築科技大學博士學位論文合正四面體，建立了絮體結構模型，計算得到的模型絮體分形維數基本與試驗中的實際絮體相符，在一定程度上能夠反映高分子絮凝黃河泥沙生成的絮體結構。Assuming the blades conduct a planar simple harmonic motion, the flows in vibrating cascades in the case of different oscillating amplitudes, different reduced frequencies and different torsional centers are computed respectively for two blade profiles. according to comparing flow calculations at different oscillation modes, the influence of the oscillation parameters " selection on aeroelastic performances of cascades is analyzed
假定葉片做平面簡諧運動，針對兩種葉型分別計算了不同振動幅度、摺合頻率及扭心位置時的振動葉柵流場，根據各種振型下流場計算結果的比較，分析了振動參數選取對葉柵氣動彈性性能的影響。Shortwave channel is time varying transmission channel. it has dispersion in frequency and time domains. this characteristics hinds the data transmi - ssion at high speed and the correction of received data. in this dissertation i have analyzed the statistic characteristic of shortwa - ve channel, established the model of shortwave channel and simulated the rayl eigh fading distribution. the technology of spreading spetrum has been proved that it has the capability for anti - multipath and discerning multipath
在短波通信中，由於通道的時間色散和頻率色散，引起多徑展寬和多徑衰落，前者限制了數據的傳輸速率，後者造成短波數據通信中出現突發錯誤，為了解決多徑效應對短波通信的影響，本文所做工作如下：首先詳細分析了短波通道的統計特性，建立其數學模型；其次分析了擴頻通信的特點，從理論上證明擴頻技術不僅具有抗多徑干擾能力，而且具有分離多徑的能力；介紹了傳統的rake分集合併技術的特點。The conventional sphere model of earth and circle model of orbit are discarded, and the ellipsoid model and the ellipse model are selected for further research, which achieves a method to determine the target position through the antenna pointing direction. and the spaceborne sar system design and simulation software is brought forth. this software accomplishes sar system coefficients design for antenna area, pulse repetition frequency, signal bandwidth, downlink data rate, radar transmitter power and satellite platform yaw steering
本文從星載雷達的星地幾何關系入手，舍棄傳統星載合成孔徑雷達研究中的球地球模型和圓軌道模型，研究了在地球橢球模型和橢圓軌道模型下由雷達天線確定目標坐標的方法，並在此基礎上研製了星載合成孔徑雷達系統設計與模擬軟體，完成雷達系統天線尺寸、脈沖重復頻率、信號帶寬、雷達信號數據率、雷達發射功率、衛星平臺的偏航牽引等幾個方面的系統參數設計以及雷達多普勒特性、雷達系統模糊、雷達定位及精度的分析，最後完成雷達回波信號的模擬。In this paper, we have studied the transmission of a plane wave through a 1d quasiperiodic or aperiodic chain by numerical method. moreover the heat conduction for these chains is calculated. it is found that the heat flux j ~ n - 1 ( 0. 5 < < 1 ), and depends on the on - site potentials
本文首先用數值方法，計算了各種頻率的平面波通過以上幾種典型的一維準周期和非周期鏈的透射系數，並據此研究了這幾種一維準周期和非周期鏈的熱通量j與粒子數n之間的關系，得出j n ~ （ a - 1 ） ， 0 . 5 1 ，與系統中在位勢的大小有關，並與其他系統的結果作了比較。At first, the dynamic mathematic model is created in the light of the known dimensions and structure. then base on the mathematic model, dynamic analysis of the system is studied by drawing the open - loop bode diagram closed - loop bode diagram and step response curve using the analysis and calculating function of matlab. the influence factor on frequency character steady and performance of the system is also analyzed
首先，根據已確定的尺寸參數和結構需要，計算並建立起系統的動態數學模型，然後在已知系統數學模型的基礎上，利用matlab語言強大的分析計算功能，對系統進行動態分析，通過畫出系統的開環bode圖、閉環bode圖及系統的階躍響應曲線，分析了系統的頻率特性、穩定性及系統性能的影響因素。When catchment area, average channel gradient and catchment shape factor of designed culvert or bridge are known, a user can be convenient to get local parameters c, e and b from standard contour charts and easy to calculate flood flow just by a calculator. design period of flood flow is enormously shortened as well as a high precision. estimated flood flow through culvert or small bridge by new calculation model is generally less than by traditional methods, so that much cost is cut down a s reducing the span of culvert or small bridge
以75000km ~ 2的川中丘陵地區為試點研究區，繪制了該地區新模型的參數等值線圖，率定了不同設計頻率的改正系數，使設計者只需在地形圖上獲取集水面積，河道平均坡降和流域形狀系數，在參數等值線圖上查得橋涵所在地的相應參數，使用計算器即可迅速計算出設計流量，大大縮短了設計周期，且精度較高，設計的洪水流量一般低於傳統方法，從而可減小橋涵跨徑，節省投資。Using pro / e ansys fem software, based on results of analyzing fem model, the article discuss the influence to the eigenfrequency of the stator in different dimension parameters of the stator loop, different pzt thickness, the influence of tooth height along circumferential direction on eigenfrequency is analyzed. it offers a foundation for optimum design the structure of the stator. fem equivalent circuit model of the ultrasonic motor has been built
利用pro / e 、 ansys等軟體建立了圓盤定子的有限元模型，通過有限元分析的方法，討論了定子圓盤各個徑向尺寸參數對特徵頻率的影響，不同壓電陶瓷厚度對定子特徵頻率的影響，以及定子齒的齒高的變化對特徵頻率的影響，為馬達結構參數的優化設計提供了依據。In the former, two computing modes of fem are built, aimed at the coupling of variable - profile pylon, curved - axis arch and flexible cable. the software algor feas is used to get the results of dynamic numerical analysis, such as natural vibration frequency, vibration mode, dynamic displacement, dynamic stress, which are compared with the results of shaking table test research to draw to important conclusions. these conclusions provide not only potent basis for the design and construction of nanjing century tower, but also reference for other pylon - cable - arch structures similar to the project
在動態數值分析中，針對世紀塔變截面的塔身，曲線軸線的拱以及柔性拉索相互耦合時清況，建立兩種有限元計算模式，利用有限元軟體algorfeas得到動力數值分析的結果，如：自振頻率、振型、動位移、動應力等等，再和振動臺試驗研究成果作比較，得到一些重要的結論，從而為南京世紀塔工程的設計和施工提供強有力的依據，而且為類以於世紀塔工程的其它塔-索-拱結構的設計也提供一定的參考。Digital frequency counter
智慧型數字頻率計數器Abstract : it provides a kind of new nonlinear integrator and its mathematical model. its frequency responses is disscussed by the harmonics linearization method. its phase lag is found to be only 27. 6, all high order harmonics are very small, and it is very resistant to disturbances. by using it, an two - objective optimum control system is designed. it has very good control performances and will have good prospects in application
文摘:提出一種新型的非線性積分器，給出它的數學模型，並用諧波線性化原理討論它的頻率特性，其幅頻特性起積分作用，而相位滯后僅27 . 6 ，高次諧波分量小，抗干擾能力強.應用這種積分器設計了一個雙目標優化的二次優化系統.模擬結果表明，系統的控制性能好，具有廣泛的應用前景The main works are as follows : 1. the paper systematically describes basic concepts and theories that form the foundation for design of general microwave filters. the topics will cover filter transfer function, lowpass prototype filters, frequency transformations, immittance inverters and the passband insertion loss under the influence of the dissipation of filter elements 2
現總結如下: 1 .對微波濾波器的設計理論進行系統的分析，闡述了微波濾波器的傳輸函數、低通原型、頻率變換、倒置變換器以及元件損耗對帶內插損的影響等方面。The studies of in - layer heterogeneity are as follows : the text depicts the characteristics of heterogeneity by calculating the coefficient of variability, kmax / k and k. max / k. min of sand layers of different sedimentous microfacies ; divides interlayer into two types, and counts their numbers, thickness, frequency and density of a single sand layer according to the characteristics of lithology and logging, finally summarizes the characteristics of interlayer distributing ; sets up five in - layer heterogeneity models and points out that the primary models are model a and c. the studies of between - layer heterogeneity are as follows : the text depicts sand layers " growth and distributing conditions by calculating the lamination factor, sandstone density and overlap coefficient ; makes certain the lithology and thickness of interlayer by the method of contrasting the typical curves
層內非均質性研究，通過計算不同沉積微相砂體滲透率的變異系數、突進系數以及級差來說明主要儲集微相的非均質特徵；據巖性及電性特徵，將層內夾層分為兩類，統計單砂層段內夾層的個數、累積夾層厚度、夾層頻率及夾層密度，並且根據夾層頻率及密度平面分布圖統計出每層的頻率相對高值區和低值區，總結夾層分佈特徵；根據物性參數隨深度的變化趨勢建立了五種儲層層內物性非均質模式，指出研究區內以a型和c型模式為主。Due to the low mechanical efficiency and long circulating period of the down - charging system of cold bed in bar production line, this paper puts forward the improving project, which adopts ethernet supplemented by dp network, applies the fm350 - 2 advanced counter and suitable maths model and combines the technique of the transducer and hydraulic pressure drive control to realize auto - control
摘要針對棒材生產線上冷床下卸鋼系統機械效率低、運行周期長，不能適應快節奏生產的現狀，採用以工業以太網為主、 dp網為輔的網路通訊，應用西門子fm350 - 2高速計數器，通過有效的數學計算模型，結合變頻器和液壓傳動控制技術，實現網路自動化控制。Based on the analysis of the kinetic track of the scallion during planting, basic relationships ' among the characteristic parameters of the transplanter with two flexible metal disks, including the velocity of the transplanter, the rate of transplanting, the spacing between seedlings, the angle of releasing seedlings, the diameter and length of seedlings, have been set up in this paper, and then a mathematic model of optimum design for the transplanter with the final planting angle of seedlings ( y = 90 ) has been formulated and solved with good results. according to the optimum solutions, a new type of transplanter with two flexible metal disks has been developed and the field tests of the transplanter have been conducted
為了實現大蔥機械化移栽，作者分析了國內各種移栽機的結構特點，確定了以撓性圓盤式栽植器為研究對象，在分析撓性圓盤式栽植器的運動軌跡和特徵參數的基礎上，完整地確立了撓性圓盤式移栽機的基本參數：栽植頻率、栽植株距、機組前進速度、輸送帶上秧槽的間距、撓性圓盤半徑、撓性圓盤的轉速、夾苗株數以及傳動比之間的相互關系，並建立了以蔥苗栽植傾角= 90為目標的優化設計數學模型，提出了撓性圓盤式大蔥移栽機的優化設計方法。According to transcendent knowledge, this algorithm classifies modulation systems by computing instantaneous frequency and instantaneous bandwidth of signal and regarding them as modulation parameters
該演算法憑借先驗知識，通過計算信號的瞬時頻率和瞬時帶寬，並以此作為制式識別參數來判斷信號的調制類型。The tradition hydrology frequency computation method is supposed that the universe is following the p - iii distribution. using the method of curve - fitting to estimate parameters according samples, and then get the design value
我們傳統的水文頻率計算方法一般都是假定總體服從p -型分佈，然後採用適線法根據樣本估計參數，進而推求設計值。The telemetry delays for each tool have been standardization as channel alphabetical letters. so the telemetry gauge and interface circuit of tools are designed in this paper. the temperature data of the new kind of telemetry tools has special format consisting of an 8 bit digital temperature wore over an 8 frame time period for its high frequency and the data of flowmeter is uplinked on two time dot to determine downhole or uphole rotational direction
本文重新設計了新型遙傳短節和參數測量儀器的介面電路，部分參數的介面電路完全採用硬體電路實現；針對溫度參數的數據頻率高於新型遙傳方式可傳輸頻率范圍的矛盾，提出了按「位」傳輸的新方式；基於流量參數特有的方向性，對流量數據採用了兩道傳輸的方式。At present, there are various methods of moving vehicle detector and identification. the system we designed for traffic information makes use of the principle of electromagnetic induction and radio frequency identification the moving vehicle detector, which is based on inductive circular loop, detects the information of vehicle according to the inductive signal. the basic information including speed and go through time can be detected to analyze oscillator frequency
目前現行的車輛檢測與識別系統的種類繁多，本系統基於電磁感應理論和射頻識別技術，採用環形線圈作為數據採集傳感器，通過對振蕩器的頻率計數測量到車輛的通過、速度等基本信息，同時啟動射頻識別系統，使讀寫器與安裝在車輛上的非接觸ic卡進行無線通訊獲取通過車輛的類型和所屬用戶等數據，並將有關數據通過rs232串口送至上位機。分享友人