計量螺桿 的英文怎麼說

中文拼音 [jìliángluógǎn]
計量螺桿 英文
metering screw
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 桿 : 桿名詞（桿子） pole; staff
  • 計量 : calculate; estimate; meterage; metering; batching; measure
  1. Scheme design for metric device of whorl - bar volume based on the methodology of functionalism

    基於功能論方法的螺桿式容積計量裝置方案設計
  2. The compact version of the plant is essentially composed of a 2 - stage plane - tary extruder, 3 - roll calender, embossing unit, take - off and cooling unit, automatic unwinder for the substrate, pull unit, thickness gauge and control system and automatic winder

    該生產線的緊湊型主要由一個2段行星螺桿擠出機、三輥壓延機、壓花機構、接取和冷卻機構、基材自動退卷機、牽引機構、厚度測量計和控制系統及自動卷取機組成。
  3. Screw bat type pre - plasticized installation, bigger capccity in piasticising, good quality in mixed refine, accuracy in measuring. minimum loss in injection pressure

    螺桿式預塑裝置，塑化能力大，混煉質量好，計量準確，注射壓力損失小。
  4. Although most part of the parameters for the design of bivis extruder currently need to be determined by adopting the analogy method, but flow capacity and condition of strength are the constraint conditions that it has to satisfy

    雖然目前雙螺桿磨漿機設計的大部分參數需要採用類比法確定，但流量和強度條件是其應當滿足的約束條件。
  5. Based on the analysis of pulping movement of material in bivis extruder, a study on the designing theory of positive directional screw in bivis extruder had been carried out, the relationship between flow capacity and basic parameters of positive directional screw in bivis extruder was established, the designing method of negative directional screw was discussed, and a basic designing train of thought of the extruder was put forward

    摘要在分析雙螺桿磨漿機中物料磨漿運動的基礎上，對雙螺桿磨漿機的正向螺旋的設計理論進行了研究，建立了流量與雙螺桿機構正向螺旋的基本參數之間的關系，討論了反向螺旋的設計方法，提出了雙螺桿磨漿機設計的基本思路。
  6. Our main products include central material supply system, series drier, automatic charging machine, single double screw extruder, series heating and cooling blending machine, crusher, cold water machine, mould temperature controller, pipe, bar section, board, pp - r pipe, pe fuel pipe, plastic dual tubing extrusion production line and granulation completed production line equipment, at same time, we also carry on various plastic machine and refrigeration engineering. the products are sold well in every province and city of the whole country and also exported to about 30 countries and areas with strong technical force, advanced equipment, scientific management system and perfect after - sales service

    公司主要產品有集中供料系統系列乾燥機自動加料機單雙螺桿擠出機粉料高速混合機粒料混合機螺旋上料機牽引機切割機離心脫水機化纖團粒機全自動擴口機全自動計量混合裝置破碎機磨粉機冷水機模溫機管材型材板材pvc管材pp - r管材pe供水燃氣管材中空壁纏繞管材硅芯管材生產線，雙管擠出電工穿線管材造粒等全套生產線設備。
  7. According to the packing materials ' demands, can choose automatic metering mechanism, automatic auger filling machine, intelligent function scale and other products suitable for automatically metering, which combined into an automatic assembly line ( also can pack through hand giving material )

    根據包裝物料的要求可配套使用自動計量機、自動螺桿充填機、智能組合秤等其它適合自動計量的產品組合成自動流水線（也可以手工供料來進行自動包裝） 。
  8. To explore why the ratio of collectable wort extract is higher than that of non - extruded, the influences of all parameters of rice extrusion system ( barrel temperature, material moisture, screw speed ) on resistant starch content of extuded rice were studied by using second - order quadratic orthogonal rotating combination design method

    摘要為探索擠壓蒸煮大米啤酒輔料麥汁浸出物收得率高於傳統不擠壓蒸煮啤酒輔料收得率的原因，用二次正交旋轉組合試驗法設計安排試驗，研究了大米擠壓蒸煮系統諸參數（套筒溫度、物料含水量、螺桿轉速）對大米抗性澱粉含量的影響規律。
  9. In addition, instead of portal brake of j93 - 1000b model, the brake device of j93 - 1000c changes into rushing board brake, thus the dependability of braking is consumedly advanced, being convenient to adjust, and the rigidity strengthening of plate design reduces the vibration noises during the working of press. with cast steel as the material of slide, slide weight of j93 - 1000c model is increased 1 thousand kgs than j93 - 1000b model with nodular cast iron as material. plus that the width from front and back of frame upright post of j93 - 1000b model is 750mm, while its 1000mm for j53 - 1000c model, increasing 250mm than the former

    J93 - 1000c螺桿螺母螺旋副使用壽命及螺桿的剛度也增加剎車裝置由原j93 - 1000b型門剎車改為j93 - 1000c推板式剎車，制動可靠性大大提高，而且便於調整，平臺設計剛度增強降低了壓力機工作中的振動噪聲j93 - 1000c型滑塊支背材質鑄鋼j93 - 1000b型的為球墨鑄鐵而且j93 - 1000c型滑塊重量比j93 - 1000b型增加1000公斤， j93 - 1000c型機架立柱前後寬1000毫米比j93 - 1000b型機架立柱前後寬750毫米增加250毫米， j93 - 1000c機身重46 . 8噸， j93 - 1000b整體機身重38 . 5噸。
  10. In addition, instead of portal brake of j53 - 1000b model, the brake device of j53 - 1000c altered into rushing board brake, thus the dependability of braking is consumedly advanced, being convenient to adjust, and the rigidity strengthening of plate design reduces the vibration noise during the working of press. with cast steel as material of slide, slide weight of j53 - 1000c model is increased 1 thousand kgs than j53 - 1000b model with nodular cast iron as material. plus that the width from front and back of frame upright post of j53 - 1000b model is 750mm, while its 1000mm for j53 - 1000c model, increasing 250mm than the former

    J53 - 1000c螺桿螺母螺旋副使用壽命及螺桿的剛度也增加剎車裝置由原j53 - 1000b型門剎車改為j53 - 1000c推板式剎車，制動可靠性大大提高，而且便於調整，平臺設計剛度增強降低了壓力機工作中的振動噪聲j53 - 1000c型滑塊支背材質鑄鋼j53 - 1000b型的為球墨鑄鐵而且j53 - 1000c型滑塊重量比j53 - 1000b型增加1000公斤， j53 - 1000c型機架立柱前後寬1000毫米比j53 - 1000b型機架立柱前後寬750毫米增加250毫米， j53 - 1000c機身重46 . 8噸， j53 - 1000b整體機身重38 . 5噸。
  11. Simulations of three - dimensional flow fields in metering section of screw during plasticization process

    塑化過程螺桿計量段三維流場的數值模擬
  12. This paper presents an investigation on a new type of rubber damper, that is, a rubber damper with honeycomb structure. the honeycomb structure will enhance the energy dissipation of a rubber damper and as a result increase the damping of the damper. the performances of honeycomb dampers are experimentally tested by a test rig. the results show that the diameter and the density of holes of the honeycomb structure are important parameters in the design of the damper. for a damper of given size, there are optimum values of both parameters with which the damper provides highest damping. additionally the honeycomb structure does not change the correlation of damping to frequency. a practical honeycomb damper is designe d and applied to inlet pipe of a screw compressor in a petroleum factory for vibration reduction. the vibration of the pipe is obviously suppressed by the damper, at least 25 %

    本文採用理論分析和實驗相結合的方法，研究了蜂窩孔這種結構因素對橡膠阻尼材料阻尼性能的影響。在自行設計、製作的懸臂式阻尼測試實驗裝置上，對蜂窩式橡膠阻尼器的阻尼性能進行了大量的實驗測試，初步找出了蜂窩孔孔徑、孔數以及預壓縮量等因素與阻尼器阻尼性能的關系。本文利用實驗研究的結論，設計了一種專用的蜂窩式橡膠阻尼器，並應用於某廠螺桿壓縮機進口管道的減振，取得了明顯的減振效果。
  13. Metering section of a screw

    擠出機螺桿的計量區
  14. Field application result shows that for eccentric screw stabilizer, there exist errors of calculated outside diameters and measured diameters, the upper stabilizer has severe influence on side force of drilling bits, and it can be optimally designed, while the bending angle of screw also has severe influence on bit side force, and it should be rationally used

    現場使用結果表明，螺桿本體穩定器採用偏心式時計算外徑與丈量直徑存在偏差；上穩定器對鉆頭側向力具有較大的影響，可以優化設計；螺桿彎角對鉆頭側向力影響較大，需合理使用。
  15. Using three - dimensional particle trajectories dispersed droplet diameter at the outlet of screw element during compounding in a co - rotating intermeshing twin - screw extruder was computed

    摘要用物料三維流動路徑結合分散模型計算了螺紋元件出口處分散相液滴的直徑，分析了螺桿轉速、擠出機產量和液滴初始直徑對末端分散相液滴直徑的影響。
分享友人
分享到 Line

分享到臉書