診斷通信系統 的英文怎麼說

中文拼音 [zhěnduàntōngxìnxìtǒng]
診斷通信系統 英文
dcs diagnostic communication system
  • 診 : 動詞（診察） examine （a patient）
  • 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
  • 通 : 通量詞（用於動作）
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 診斷 : diagnose; diagnosis; diacrisis
  • 通信 : communication; communicate by letter; correspond
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. Abstract : in this paper, the significance of remote monitoring and fault diagnosis system for the pipe laying pump units in petroleum conveyance process is discussed. the communication principle and particular of remote monitoring and fault diagnosis system for pump units are analyzed. the hardware configuring and software algorithm of this system are constructed, and then, advantage and benefit out of this system are pointed out

    文摘:論述了原油輸運過程中的加壓泵機組遠程監測及故障診斷系統的意義，分析了輸油泵機組遠程監測及診斷系統的通信原理和特點，建立了實現該系統的硬體結構和軟體體系，最後說明了採用該系統的優勢。
  2. On the other hand, boundary - scan technique intelligent fault diagnostic method was applied to practice. for most digital system, devices with boundary - scan architecture are broadly used. only using four line or five line to connect pc parallel port with cut tap ( test access port ), all the ptvs can be loaded to cut and all homologous prvs can be taken back to intelligent fault diagnosis system

    至於本文採用邊界掃描測試故障診斷技術，是考慮到本系統的通用性和簡潔性，因為對于大多數數字系統而言，具有邊界掃描結構的器件己廣泛應用，本文只需4條或5條信號線就能將pc機和被測邊界掃描電路連接起來，由此極大地簡化了智能故障診斷系統中為實現ptvs加載和prvs獲取而專門設計的介面板電路。
  3. Using the computer, network and communication technology, the manager can mast the remote equipment running station and control the equipments with sensors installed in working site. the supervision system has good flexibility and expanded ability, hence the stability of mobile system has been improved. the data picked up by sencors has been transferred to the remote monitoring center with communication networks

    目前遠程嵌入式監控系統已經成為監控系統的發展趨勢，現代遠程監控技術，藉助于計算機，網路和通信技術，管理者可以依靠安裝在現場的各種傳感器，實時了解現場狀況，對現場設備進行監視診斷和維護，使整個系統具有高靈活性和可擴展性，同時也增加了被監控系統工作的穩定性。
  4. The new instrument add a sensor that can gather the signal of the stator inductive current. and by analyzing the signal of the stator inductive current, judge the moving state of the electromotor. this instrument is mainly diagnosis the follow fault : the fragment of the bar in the rotor fault, the fault of eccentricity of the interspace between the rotor and the state of the electromotor.,

    本儀器是在回轉機械故障診斷與監測系統的基礎上開發的，同時，根據電機這種特殊設備的實際情況，增加了電機電氣信號的檢測，即通過對電機定子三項繞組電流信號的變化分析，來找出電機的電氣故障，主要是轉子斷條，氣隙偏心故障以及定子等故障。
  5. On top of its conventional activities of signal magnification, reshaping, filtering, sampling, a / d transformation and scale switching, the intelligent sensor system can perform kinds of advanced operations such as on - line storage of parameters, real - time data processing, self - diagnosing of the system and so on. because of its communication interface with pcs, it serves as intelligent plug & play network sensor

    它除了能完成對傳感敏感器件的信號進行放大、整形、濾波、采樣、 a d變換及標度變換外，還可實現參數在線存儲、數據實時處理、系統自我診斷等功能，並可以通過其通訊介面與溫室現場總線相接，組成即插即拔的智能網路傳感節點。
  6. Since the suggested method makes a significant improvement in wind speed, it is more suitable for wind field estimation over complex terrain than other methods which only concerns the effect of distance. then we calculate the wind change with evaluation, last we can conclude the wind abase the hilly terrain, we find the wind in westward and center plain is much smaller than other area. while the wind in northward hilly area is much bigger with the hilly arising. the wind of chongqing is the biggest period in spring ( april ), the smallest period in winter ( january ), the wind in summer ( july ) is bigger than its in autumn ( october )

    本文利用重慶及其周邊地區的常規氣象站的1951 ? 1980年30年的風速平均資料，針對復雜地形風速診斷，以地理信息系統為數據處理平臺，根據重慶1 ： 25萬dem數據，來獲得重慶市實際復雜地形的高程，提出了一種適合於起伏地形的權重內插方法，通過引入一個表示地形起伏變化程度的因子，構造了一種新的權重函數，來處理復雜地形上的風速，通過與只考慮距因素同反平內插方法比較發現，本方法更適合在起伏地形條件下使用；然後根據經驗公式在地形上進行計算，得出重慶地區起伏地形下的風速分佈；得出重慶市的西部、中部平原地帶風速較小，而北部山區隨海拔高度升高風速也較大；重慶市風速最大時期為四月份，冬季一月份最小，夏季（七月份）大於秋季（十月份） 。
  7. ( 4 ) since there is no perfect theoretical guide, the characteristics of orthogonal wavelet, semi - orthogonal wavelet and biorthogonal wavelet in signal decomposition and reconstruction are compared, and the conclusion of the study demonstrates that semi - orthogonal wavelet is a good wavelet for fault diagnosis in tilting control system of tilting train. a new approach is presented for deciding the fault threshold. ( 5 ) a generalized wavelet neural network is put forward by integrating wavelet analysis with neural network

    （ 4 ）針對小波基的選擇缺乏完善理論指導的實際情況，通過對常用的正交、半正交、雙正交小波基提取信號特性的比較，確定出了適合擺式列車傾擺控制系統故障診斷的小波基? ?半正交小波基，並提出了一種新的確定故障檢測閾值的方法，可以快速地檢測出故障發生時刻。
  8. Design of knowledge system of a communication equipment fault diagnosis

    一種通信設備故障診斷知識系統的設計
  9. ( 3 ) study deeply the structure of fat 16 file system and the characteristic of flash disk, and develop the file management software of flash disk to manage nc files effectively according to the management idea of fat 16 file system. ( 4 ) research the module and protocol of reliable communication in serial network, which are composed of arm main control board, dsp motion control board, keyboard board, i / o control board and encoder signal collection board, and then develop communication software of the serial network. ( 5 ) study the principle of displaying char in lcd and the method of embedding font library into operating system, and research deeply the method of embedding chinese font library into os in the light of the characteristic of chinese

    本論文的主要研究內容如下： （ 1 ）研究uc os -實時嵌入式操作系統在硬體平臺上的移植及其佔先式內核的任務調度原理，合理分割銑床控制系統的管理任務，根據任務的要求賦予不同的優先級和調度時間，保證任務的執行效率和實時性； （ 2 ）開發底層設備驅動程序和應用程序介面（ api ）函數，以便於進行系統應用軟體的開發； （ 3 ）深入研究fat16文件系統的結構和固態盤的硬體特性，參照fat16文件系統的管理思路，開發固態盤文件管理軟體以有效管理nc代碼文件； （ 4 ）深入研究由arm主控板、鍵盤板、 i o控制板、編碼器信號採集板等裝置組成的串口通訊網路可靠通信的模型及其通訊協議，開發串口通訊網路通信軟體； （ 5 ）研究字元的顯示原理和在操作系統中嵌入字庫的方法，在此基礎上結合漢字的特性深入研究中文字庫的嵌入方法，開發中文字庫嵌入軟體，滿足開發操作界面的信息要求； （ 6 ）深入研究三維圖形坐標變換的原理，開發實用的三維加工軌跡顯示軟體，便於操作者對零件的加工過程進行監控和診斷。
  10. This paper deals with synchronous measure technology of the cylinder pressure with the engine cold start by adoping micro - chip aduc812, and it discuss the analysis of breakdown of engine cold start with the mixture of technology of information. through the analysis of the parameters of cylinder pressure of the engine cold start, turning speed and starting electricity, and according to the measure data and witness, a theory is to be inferred, and with the help of breakdown - checking systems, the engine piston groups and the breakdown of starting system can be judged. at last, the. remote measure technology of cylinder pressure ' s parameters

    本文採用微處理器晶元aduc812研究發動機冷起動氣缸壓力的同步測試技術，討論了基於信息融合技術的發動機冷起動故障診斷方法。通過對發動機冷起動氣缸壓力、轉速、起動電流等參數的測試，根據測試數據和證據推理理論，藉助故障專家系統，判定發動機氣缸活塞組以及起動系的故障。最後研究了氣缸壓力等參數的遙測技術。
  11. For modern communication chamber, it ' s very important for management to get the condition of these chambers and prevent fire. now supervising modern communication rooms " condition is developed towards multi - way integration, combination of supervising - diagnostic - maintenance determination and network, and then condition supervision has typical character of information fusion. the quality of information could be improved by making full use of multi - datasourse inter complementarily and redundance. the problem such as much quantity, extensive distribution, supervisement, diagnostic and management and so on could be settled through network, at the same time the remoted condition supervising system based on multi - sensor multi - layer information fusion could be realized conveniently

    當前現代機房的狀態監測正朝著多種方法集成、監測?診斷?維護決策相結合以及網路化的方向發展，使得狀態監測具有典型的信息融合特徵，充分利用多源數據的互補性及冗餘性來提高結果信息的質量；通過網路解決系統測點數量多、分佈廣、監測、診斷、操作和管理困難等問題，使基於多傳感器、多層次信息融合的遠程狀態監測系統得以方便地實現。
  12. And production rules are used to express the expert ’ s knowledge. model bases and reasoning machine are accomplished by using visual basic 6. 0 programming technology ; interface follows the windows ’ pattern. the peanut cultivation expert systems can realize functions such as simulating and predicting peanut ’ s growth and development, designing peanut cultivation

    該系統可以根據花生種植地區的氣候、土壤和生產條件，實現花生生長發育的模擬與預測、花生栽培方案的設計、花生病蟲害的診斷與防治、信息咨詢和花生知識學習等功能，並能夠通過知識庫管理和維護系統進行知識的修改、添加和刪除，實現知識的獲取和管理功能。
  13. The rmdms was distributed, and could be divided into work fields and diagnosis and maintenance center, the former acquired and supplied the latest data of the complicated devices, the latter supplied all kinds of diagnosis and maintenance resources for the work fields ; the rmdms was the integration of several subsystems logically, which working in coordination to show the functions of condition monitoring, diagnosis and maintenance, resources marshalling and communication

    系統在物理上是分佈的，分為現場端和診斷維護中心，現場提供設備運行狀態的一手資料，中心為現場提供各種診斷維護資源；在邏輯上，整個系統是多個功能子系統的有機集成，它們協同展現了狀態監測、診斷維護、資源調度、交互通信等功能。
  14. Multi methods of signal analysis and fault diagnosis, such as wavelet transform, emd analysis and fault diagnosis based on neural network, are provided in the system. by message board, users can ask for help if they happen to meet some problems. they can also bring forward their opinions and suggestion about this system to make remote maintenance more and more mature

    此遠程維護系統提供了多種診斷信號分析方法和多種故障診斷方法，如小波分析、 emd分析、神經網路故障診斷、 cbr專家系統等；同時，通過留言板用戶還可以針對特殊疑難故障請求遠程維護中心的幫助，或對本系統提出改進意見和建議。
  15. With the help of dynamic qualitative information of working marine diesel power equipment in this field and expertise, a new long - distance oil monitoring expert system of marine diesel power equipment has been proposed and developed with the characteristic of expounding the dynamic features of marine diesel power equipment from the perspective of chaos knowledge, possessing intellectualized auxiliary decision - making mechanism based on fuzzy reasoning and neural network reasoning, utilizing mathematic analysis model established by means of track facility states of chaos vector and capable of evaluating the analysis results of oil monitoring facil ity ' s development of engine power and its working conditions accurately

    然後，結合廣泛搜集的本研究領域內船舶柴油機動力裝置在運行中的動態定性信息與專家經驗，研製開發了運用混沌學的觀點闡釋船舶動力裝置的動力特性，並擁有基於模糊推理與神經網路協作推理的智能化輔助決策機制，採取通過求取設備狀態混沌向量等方法建立的數學分析模型進行數據分析，能準確地評價船舶柴油機動力裝置油液監控設備狀態變化趨勢及其運轉狀況的遠程輪機油液監控診斷專家系統。本文研製開發的遠程輪機油液監控診斷專家系統在internet intrabet網路環境下，具有遠程智能專家診斷的特點。
  16. The system, which is composed of remote monitoring devices, gsm communication system and monitoring center, is a compositive subject of technology of teletransmitting, information, health care and embedded system design. in the remote transmitting system for physiological signals those abnormal physiological signals, after being inspected and analysed, will be sent to monitoring center by gsm

    該系統融合了遠程通信技術、信息學技術、醫療保健技術和嵌入式系統設計技術，由遠端監測設備、 gsm通信系統及監護中心組成，主要實現生理參數實時採集、處理、控制、傳輸和輔助診斷功能。
  17. The company ' s smart sis safety instrumented systems will also be installed on an independent network, with diagnostics communication to the process systems

    艾默生的智能sis安全儀器系統也將安裝在一個獨立的網路里，向過程系統提供診斷通信。
  18. The remote condition monitoring and fault diagnosis system implement the monitoring and diagnosis in different area, which means the system can inspect in time both the current condition and the history information of machine. moreover, expert - diagnosis and consultation can be held by network, which can greatly enhanced the accuracy and shooting percentage. so it has good application prospects

    遠程狀態監測與故障診斷系統一方面可以實現異地的監測與診斷，通過internet及時了解設備的運行狀況和相關歷史信息；另一方面，通過網上專家診斷和多個專家的網上會診可以大大提高設備故障診斷的準確率和命中率，因此有著良好的應用前景。
  19. By investigating the particular requirements for building knowledge base and inference mechanism of the expert system based on web, the methodology for transferring the isolated diagnosis resources into ercd ’ s service cell is given

    通過研究web環境下遠程診斷專家系統對知識庫及推理機實現的特殊要求，分析討論了信息孤島式診斷資源和服務單元作為可用遠程協同診斷服務單元提取呈現的方法。
  20. Aiming at four analysis measures - spectrometric, ferro graphic, routine, and particulate counting, the author has established time - sequence model based on fuzzy estimation regulations, tentatively provided analysis standard criterion for failure analysis, and proposed fuzzy systematized model for diagnosis system of lubricant monitoring expert ; employing mathematical methods of fuzzy analysis, the author has established analytical synthetic evaluation model, analyzed the reasonability of analytical measures in lubricating oil and equipment condition evaluation, and provided extraction method model of information regulations for diagnosis system of lubricant monitoring expert by means of analyzing par ameters

    針對光譜、鐵譜、常規理化、顆粒計數四種分析手段，建立了基於模糊判斷規則的時序模型，並建立了輪機油液監控專家診斷系統所需的模糊分類器模型；採用模糊分析的數學方法，建立了綜合分析評判模型，並對各分析手段在潤滑油評定和評判設備狀態時的合理性進行闡述，為輪機油液監控智能診斷專家系統提供了一種通過特徵參數分析與處理，建立的規則信息提取方法和模型。
分享友人
分享到 Line

分享到臉書