試切調整 的英文怎麼說
中文拼音 [shìqiēdiàozhěng]
試切調整
英文
developed setting- 試 : 名詞（古代占卜用的器具） astrolabe
- 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
- 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
- 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
- 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
-
Meixing electronics factory is major in the vacuum tube stereo power amplifier, which is located in the nanhai city ， owned a workhouse over 1300 square meter, with five plant, they are box, seal and transformer circling 、 debugging & check, we also have the machine process, such as milling machine 、 punch 、 drill press 、 electric welding 、 matrix 、 incision machine, and radio tube test machine. we have realize the product line manufacture, the monthly whole output is over 200 sets
美星電子是一個專業製造真空管身歷聲功率放大器的加工廠，位於廣東南海市黃岐工業區，擁有廠房一千三百平方米，工廠分機箱加工、焊接組裝、變壓器繞制、煲機老化、調試檢測五個車間，機械加工設備擁有銑床、沖床、創床、鉆床、電焊、模具製作、切割等二十多臺，電子管及整機檢測調試儀器十餘臺，該廠實現了配套設備、流水作業，每月可生產膽機二百臺以上，可謂中國專業生產膽機最大規模的工廠。In this thesis it was proposed to simulate the drawing, trimming, flanging by using error - adjustment method. the initial trimming lines would be adjusted and optimized in the computer by adjusting error. if the shape error between the flanging boundary line and the target is larger than prescribed, the redundant area is subtracted from the initial blank by some amount of volume along the deformation path, and the insufficient volumes are added to the initial blank by the same amount
本文提出，利用基於變形路徑的誤差修正法（ error - adjustment ） ，結合cae技術將對初始修邊線的調試過程在計算機中進行模擬（包括拉延、修邊、翻邊、整形等）計算，通過控制翻邊后零件成型邊界與實際目標輪廓之間的尺寸誤差來優化修邊線，如果初始切邊、翻邊后的輪廓與目標體的邊界存在較大偏差，則初始切邊輪廓中多餘部分單元將沿其變形路徑以相同體積量被切除，不足部分則沿其變形路徑以相同體積進行補償。Above all, the paper offers the detailed introduction for the hardware system of mould industry and electric spark machining. this article sets forth the thought requirement, the principle of recording, the thought of realizing, the puzzles in designing and the process of adjustment during collecting course, conversion system between light and electron in the track system of optics
為此，本文對模具工業生產及數控電火花線切割機的硬體系統做了詳細的介紹，重點闡述了光學跟蹤系統中光電轉換系統的設計及數據採集、處理軟體的整體要求，記錄原理，實現思路，設計過程，以及調試誤差分析。
分享友人