誤差分配碼 的英文怎麼說

中文拼音 [wùchāfēnpèimǎ]
誤差分配碼 英文
error distributing code
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 碼 : Ⅰ名詞（表示數目的符號或用具） a sign or object indicating number; code Ⅱ量詞1 （指一件事或一類的...
  • 誤差 : error
  1. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  2. In order to improve the quality of the voltage signals, this paper has adopted the scheme of three phases and six organs in signal - generator part, which can eliminate the errors caused by the assembly warp and the zero shift of organs. this paper also has analyzed the distribution and varying rules of the magnetic field in the signal - generator part, then based on the conclusion of the analysis improved the structure of signal - generator, which could completely eliminate the noise signal caused by the roughness of the face on the magnetic steel ring. the improvement not only met the requirement of this study, but established the theory foundation for the super - high precision magnetic encoder in future research

    因此，為提高原始電壓信號的質量，本文採用三相六元件的信號發生方案，通過差分處理濾除了由於裝配偏差和零點漂移帶來的信號誤差;本文對編碼器信號發生結構進行了磁場分析，依據磁場分析的結論對編碼器常用的信號發生結構進行了改進，改進后的結構利用積分原理在理論上能夠完全消除信號中由磁鋼環表面粗糙度引起的信號噪聲，進一步提高了信號質量，此結構不僅滿足了本課題的需要，而且為今後研製超高精度的磁電式編碼器奠定了理論基礎。
  3. An optimal subband rate allocation algorithm in mean - squared error ( mse ) minimization sense was proposed, which achieves persistent optimal rate - distortion performance under any given rate constrains

    提出均方誤差最小意義上的最佳三維子帶碼率分配演算法，該演算法在任意給定碼率限制條件下都能獲得最優率失真性能。
  4. This paper achieves expected digital filters program through algorithms descriptions, analyzing and realization, simulation, comparing on error and speed. this paper achieves expected digital interpolations program through algorithms descriptions, analyzing and realization, simulation, comparing on error and speed

    本文應用matlab信號處理工具箱，通過對數字濾波器演算法的描述、演算法分析、實驗模擬、誤差比較，及性能比較，最終獲得滿足要求的數字濾波程序，並編譯成c + +源代碼文件配合主程序調用，完成了系統聯調。
分享友人
分享到 Line

分享到臉書