調整圓弧 的英文怎麼說

中文拼音 [diàozhěngyuánhú]
調整圓弧 英文
adjusting arc
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. In this process, the thesis discusses detailedly the method which can improve the resolving power in measuring component and can deal with the probe circuit, and puts forward the design method of applied circuit. then the thesis discusses the methods of line and circle interpretation

    接著又討論了計算機數控系統的控制策略，主要包括：知道預定軌跡的直線與圓弧插補的方法、連續掃描系統的控制策略、 pid調節器的設計及pid參數的整定方法等。
  2. The paper describes the feature of double circular arc spiral bevel gears, basing on such gears manufacture theory, the paper depicts how to form the double circular arc spiral bevel gear tooth profile, at the same time, depicts its meshing theory and derives its tooth profile equation. basing on fsh short tooth, the paper derives the tooth depth equation, describes its manufacture technology, makes out this tooth propile single side method regulation calculation card

    本文從弧齒錐齒輪加工原理出發，闡述了雙圓弧弧齒錐齒輪副點嚙合齒面的形成原理，同時還論述了雙圓弧弧齒錐齒輪基本嚙合原理，推導出了具有普遍形式的齒面方程，同時以fsh短齒形為藍本還推導出了雙圓弧弧齒錐齒輪齒厚計算公式，闡述了雙圓弧弧齒錐齒輪的製造工藝，編制了雙圓弧弧齒錐齒輪單邊切削法機床調整計算卡。
  3. The whole software is composed of four modules :, the scaling module, the hangingjgear, the process module. the three modules are independent, moreover they are interrelated, which make then arc - gear - capp is a whole process

    各個模塊既是獨立的，可以單獨調用其中的任何一個模塊；又是相互聯系的，構成一個整體，從而實現工藝規程的制定、機床掛輪的選擇、尺寸測量、精度與公差的選擇等完整的圓弧齒輪的加工過程。
  4. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  5. By adjusting the given tangent vector, the parametric rational arc spline also has convexity preserving property and monotonicity preserving property

    在實際操作中，通過調整一側端點的切向量，可使上述圓弧樣條曲線保凸，保單調。
分享友人
分享到 Line

分享到臉書