調整拉線 的英文怎麼說

中文拼音 [diàozhěnglāxiàn]
調整拉線 英文
adjuster cable
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 拉 : 拉構詞成分。
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  • 拉線 : backguy; gur; tie line; guy wire拉線板 strain plate; 拉線工 lineman; 拉線盒 terminal box; 拉線機 ...
  1. Of, relating to, or characteristic of a style in art and architecture developed in europe from about 1550 to 1700, emphasizing dramatic, often strained effect and typified by bold, curving forms, elaborate ornamentation, and overall balance of disparate parts

    這種風格強調拉緊的效果，其特徵是有大膽的曲線結構、復雜的裝飾和無聯系部分間的整體平衡
  2. Wool skin are transpted by circle pressed - line convey, length of wool can be controlled from 5mm to 50mm, there are four screwing balades on the top, the convey is made of high tensile rubberiaed fabric, transpt table can be remed to adjust length of wool

    毛皮的進給是採用循環壓線式傳送，能夠隨意剪毛從5毫米到50毫米，上刀裝有4片螺旋式滾刀片，傳送帶選用高密度抗拉膠布帶，傳送臺能前後移動用來調整剪毛長度。
  3. Wool skin are transported by circle pressed - line conveyor, length of wool can be controlled from 5mm to 50mm, there are four screwing balades on the top, the conveyor is made of high tensile rubberiaed fabric, transport table can be remored to adjust length of wool

    毛皮的進給是採用循環壓線式傳送，能夠隨意剪毛從5毫米到50毫米，上刀裝有4片螺旋式滾刀片，傳送帶選用高密度抗拉膠布帶，傳送臺能前後移動用來調整剪毛長度。
  4. According to the design theory of the cable - stayed bridge and to the feature of the cantilever construction the authors propose a construction control method called optimum completion state method ( ocsm ) for rc cable - stayed bridges in the proposed method, the optimum completion state is regarded as the final target of the construction control, and the optimum construction state at each construction stage is taken as the technical route the key of the method is to properly choose or adjust the cable forces the objectives function of optimization is to minimize the elevation error of the girder under the constraint condition that the internal forces ( bending moments ) of the girder are bounded the optimization variables are the cable forces on the basis of the above principles, a optimum model for a construction step is established and cable force adjustments can be found for each construction step in this model, the creep and shrinkage effects of concrete have been considered a bridge example is given which shows that the final state of the bridge is very close to the design aim and that this method is much better than the so - called double - control method the example is a good illustration of the soundness and practical value of the proposed method

    根據現代斜拉橋結構設計理論和懸臂施工方法的特點，提出了以最佳成橋狀態作為施工控制的最終目標，以實施最佳施工階段為技術路線，以索力調整為核心內容的斜拉橋施工控制理論，簡稱為最佳成橋狀態法；以斜拉橋主梁標高誤差最小為目標函數，以主梁內力（彎矩）為約束條件，以索力為優化變量，建立了最佳施工階段的索力調整計算模型；推導了考慮徐變收縮效應的索力調整計算公式；用最佳成橋狀態法對一實橋工程進行了施工控制全過程計算研究，得到的成橋狀態與設計目標相當接近，優于該橋以「雙控」為控制目標的實測結果，有力地證明了本文方法的正確性及其工程實際價值
  5. In this thesis it was proposed to simulate the drawing, trimming, flanging by using error - adjustment method. the initial trimming lines would be adjusted and optimized in the computer by adjusting error. if the shape error between the flanging boundary line and the target is larger than prescribed, the redundant area is subtracted from the initial blank by some amount of volume along the deformation path, and the insufficient volumes are added to the initial blank by the same amount

    本文提出，利用基於變形路徑的誤差修正法（ error - adjustment ） ，結合cae技術將對初始修邊線的調試過程在計算機中進行模擬（包括拉延、修邊、翻邊、整形等）計算，通過控制翻邊后零件成型邊界與實際目標輪廓之間的尺寸誤差來優化修邊線，如果初始切邊、翻邊后的輪廓與目標體的邊界存在較大偏差，則初始切邊輪廓中多餘部分單元將沿其變形路徑以相同體積量被切除，不足部分則沿其變形路徑以相同體積進行補償。
  6. Firstly, the method used adaptive propagation rule to get local and global spatial information, then, using this information to non - linear enhances the image contrast

    首先使用自適應傳播機制求出紅外圖像的各種局部空間信息，然後對各種信息進行非線性拉伸調整，得到增強后的圖像。
分享友人
分享到 Line

分享到臉書