調節閥定位器 的英文怎麼說

中文拼音 [diàojiéfádìngwèiqì]
調節閥定位器 英文
positioner of control valve
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 節 : 節構詞成分。
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 調節 : regulate; adjust; monitor; measure; take care of; condition; regulation; adjustment; conditioning...
  1. Process equipment under different choice of pneumatic or electric implementing agencies, forming an aerodynamic ball valve and electrical ball valve, such as pneumatic ball valve regulated to achieve proportional valve positioner to be allocated, such as the electric ball valve to be regulated to achieve proportional election electronic implementing agencies or distribution of electric servo amplifiers

    根據工藝設備不同可選用氣動或電動執行機構，分別組成氣動球閥和電動球閥，其中氣動球閥如要實現比例調節須配閥門定位器，電動球閥如要實現比例調節須選電子式電動執行機構或配伺服放大器等。
  2. Then pid flow rate control algorithm is introduced. all experiments made in this chapter are about measuring the valve parameters according to spool positions, single actuator flow rate control by the calculated flow rate feedback control method, free flow rate dividing control under the sufficient pump discharge flow rate situation, proportion flow rate dividing and flow rate dividing based on meter - in flow rate feedback control method under insufficient pump discharge flow rate situation. the results of all experiments proved that the method presented in this thesis is an effective way to overcome the unreasonable flow rate dividing when simultaneously operating multi - actuators with different inertia loads

    第四章介紹了多執行器復合控制實驗系統和實驗方法；介紹了實驗採用的流量控制的pid演算法；並測定了執行器控制閥和閥芯位移相關的系數；做了單個執行器計算流量反饋流量控制、流量足夠情況下多執行器流量任意分配、流量不足情況下多執行器按比例調節流量分配和多執行器進油側流量反饋分流控制實驗；通過實驗說明了論文提出的分流控制方法能實現大小慣性負載復合操作時的合理分流。
  3. Because the output pressure signal of the manoeuvring valve ( pos. no. 01 - ) corresponding to the regulating handle position determines the output rate of the p. g. governor through the 3 - way valve ( pos. no. 29, lower frame )

    因為操縱閥01 -相應調節手柄位置的輸出壓力信號決定調速器輸出比率通過三通閥29 ，下位。
  4. Due to the component of natural gas is very complex in different zone of our country, the product has taked on special design, it set up moore component factor of thirteen kinds, which offer user to select and setup, so as to satisfy measurement for contains various component natural gas, at the same time established many take - pressure way in order to suit to different measure device, and have automatic calculate and display super - compression factor function

    A q型操作器輸出svout ： 010ma 420ma 05v 15v信號，可直接驅動執行機構變頻器或再由伺服放大器去驅動電動調節閥門或由電氣轉換器和閥門定位器去驅動氣動薄膜閥。操作器處于自動工作狀態時，其信號輸入svin和操作輸出信號相當於是直通的。以實現dcs系統或調節器對執行機構的自動控制。
  5. By use plc, system can complete function as follow : this auto - control system be applicable to the temperature and smoke and dust the deal the variety quick, control the process is difficult with the operation is ; by the temperature controlor can automatically follow to the wet tower " exit temperature, error in the ? 3 v including ; by to automatically spray fog to lower the electric resistance, with the function for full the electricity equipment accepting the dust ; because of adopting feedback closed loop, and come to a to respond to the speed quick, constant temprature control the accuracy is high ; because of adopting the sensors, and make the system circumstance to leak water quick ; system have many control parameter can set exit control temperature and adjust value low limit by key ; can communication with remote computer and have remote control

    通過使用plc ，使該自控系統可以完成如下功能：適用於溫度及煙塵量變化快、控制過程難以操作的場合；通過溫控表自動跟蹤增濕塔出口溫度，誤差達到3以內；通過自動噴霧來降低粉塵比電阻，以此充分發揮電收塵器的作用；由於採取了閉環反饋迴路，達到了響應速度快，恆溫控制精度高；通過使用各種檢測傳感器，使得異常情況泄水快；該自控系統具有多套控制參數，增濕塔出口控制溫度及調節閥下限值可通過按鍵設定；可與上位機通訊，具有「現控遠控」功能。
  6. Industrial - process control valves. part 6 : mounting details for attachment of positioners to control valves. section 1 : positioner mounting on linear actuators

    工業過程調節閥.第6部分:調節閥與定位器連接用安裝細節.第1節:安裝于線性傳動裝置的定位器
  7. Industrial - process control valves - part 6 - 2 : mounting details for attachment of positioners to control valves - positioner mounting on rotary actuators

    工業過程調節閥.第6 - 2部分:定位器裝到調節閥的安裝細則.旋轉傳動裝置上定位器的安裝
  8. Intelligent given manipulator have all characteristic of on - off control meter with universal division number, when automatic operating, measured value compares with given value, by which determine direction or reversion for manipulator output, double screen numeric tube display, up screen display measured value, low screen display given value

    智能閥位外給定pid控制調節儀採用先進的微處理器進行智能控制，適用於需要進行高精度調節控制的系統，能根據被控對象自動演算出最佳調節參數。
分享友人
分享到 Line

分享到臉書