調速閥 的英文怎麼說

中文拼音 [diàosùfá]
調速閥 英文
compensated flow control valve
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 閥 : 名詞1 （指在某方面有支配勢力的人物或家族） established house or power group; a powerful person or...
  1. This paper supplied a new way through variable frequency variable speed ( vfvs ) to change its output flow rate and adding a constant - pressure - drop valve, which could solve the defects in hydraulic pressure servo control system, such as low efficiency in control system, short life, poor ability in resisting pollution, low efficiency in driving system and flow rate, pressure pulse. and this way was proved to be effective

    本論文針對傳統伺服控制系統效率不高、元件壽命短、抗污染能力差、驅動系統效率低、存在流量及壓力脈動等缺陷，利用先進的交流變頻調速技術改變液壓泵轉速的容積調速新方法，提出了在液壓系統中加一個定差減壓閥的新思路，較好地解決了液壓伺服系統存在的上述問題。
  2. Water feeding framework takes electromagnetism water valve as administration component and is added relief valve for stabilizing hydraulic pressure ; the system has large, middle and small water valve that changes unlock combination of electromagnetically operated valve, which can get seven different water flux ; if it is necessary, it should adopt microseism water feeding that can make water feeding get stepless timing

    3加水機構加水機構採用電磁水閥作為執行元件，加入調壓閥穩定水壓，系統共設大中小三路加水閥，變化電磁閥的開啟組合，可以得出7種不同的加水流量，必要時採用脈動加水法，可使加水達到無級調速。
  3. In this study, the load charateristics of submergible centrifugal pump and the influence of various regulating methods on energy dissipation are analyzed. the loading capacity of the submergible motor in variable speed drive control process is analyzed. the papers simple discribe the basic structure of the variable speed drive system in electric submergible pump > principle of pwm inverter and the basic structure of igbt

    在研究中，對潛油離心泵負載性能以及閘閥調節和調速調節對能耗的影響進行了分析；對潛油電動機在變頻調速的負載進行了分析；對潛油電泵變頻調速系統的基本結構、 pwm逆變器原理以及igbt的基本結構進行了簡單介紹。
  4. In the paper, on the basis of research of static state and transient state in the scr and series connection valve circuit, the high voltage scr changing current valve device has been developed for ac - dc - ac high voltage commutatorless motor. the series connection valve circuit has been designed and simulated. the hardware design and software programming of trigger pulse system and monitoring system in the photo - electronic - photo fashion has been completed

    無換向器電動機在火電廠等工礦企業的電機調速節能領域中有十分廣闊的應用前景，本文在對晶閘管元件和串聯閥電路的靜態特性和動態特性研究的基礎上，研製了用於交直交電流型高壓無換向器電動機的高壓晶閘管換流閥裝置，進行了串聯閥電路的設計和模擬，完成了電光電方式的觸發脈沖系統和監測系統硬體設計及軟體編程，並進行了裝置的實驗調試。
  5. When the governing valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod increased, meanwhile, it ' s time of rise, time to peak and the governing time all increased. at the same time, the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    當出口節流調速系統的回油路上串接調速閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是增加的，上升時間、峰值時間以及調整時間也是增加的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。
  6. The fuyite brand valve control timing hydraulic coupling can resolve the above problems well, and carry out " soft start " thus

    福伊特閥控調速型液力耦合器能夠很好地解決以上問題，從而實現「軟啟動」 。
  7. Through analyzing the figure of energy wasting of pump, the quality in pipes is direct proportion of the speed of pump if the speed of pump is reduced. the power of electromotor fell the cube of the speed of pump. so the energy wasting of constant pressure water supply based on variable frequency speed regulating technology is envident less than the traditional mode is used throttle to supply water

    分析水泵工況的能耗比較圖，可以看出利用變頻調速實現恆壓供水，當轉速降低時，流量與轉速成正比，功率以轉速的三次方下降，與傳統供水方式中用閥門節流方式相比，在一定程度上可以減少能量損耗，能夠明顯節能。
  8. The head part is applied a screw pole and is go up and down the system, efficient implementation machine tool coarse control

    液路加裝單向調節閥，有效控制鉚接速度。工作臺部分應用大行程絲桿升降系統，有效實現機床粗調。
  9. It has the advanced radial technology and the movement path likes 11 pieces plum blossoms shape, this machine uses a head screw pole to go up and down to control the power head, it has the enlarged bench, and air current double - direction adjusting valve to controlled the riveting speed effectively. the electricity system added the counter to count the work piece which was be processed, he time relay control the riveting times

    Jm3tq - d是汽動類小型徑向鉚接機，與jm3tq - b和jm3tq - c相比，提高最大工作行程到40mm ，除應用有國際先進的11瓣梅花徑向鉚接技術外，該機採用頭部絲桿升降粗調，加大了工作臺面，氣路加裝雙向調節閥，有效控制鉚接速度。
  10. The second chapter simply introduces the development of alternate asynchronous inverter technology and retrospects some types of energy - saving systems for hydraulic elevators. then the working principles of the project are discussed and analyzed at four different working status, i. e. light load upwards, heavy load upwards, light load downwards and heavy load downwards. and the chapter focus on the introduction of structure design of pump station, calculation and type selection of pump / motor reversible units, research on oil leakage principles of accumulator circuit, design of accumulator - pump / motor pressure - energy transformer and integrated valve blocks, etc. the last but not the least, the electrical wiring of vector inverter control cabin and design of computer control and data acquisition system are introduced

    論文第二章首先簡單介紹了交流異步電動機變頻調速技術的發展概況，在回顧電梯液壓控制系統節能技術的基礎上，介紹了本課題研製的「採用蓄能器的液壓電梯變頻節能控制系統研究」的基本原理，分析了動力系統在電梯轎廂輕載上下行、重載上下行等四種典型工況下的基本工作狀態和工作方式；詳細地介紹了本課題節能系統液壓動力泵站的結構設計和參數設計，重點研究了液壓動力泵站的結構設計、液壓泵馬達可逆性問題及其選型設計計算、蓄能器迴路泄漏油損失機理的研究及其補償裝置的設計、蓄能器-泵馬達壓力能量轉換裝置的設計、多功能集成控制閥組的設計等內容；最後簡單介紹了本課題矢量控制變頻控制櫃的外部附件電氣接線、計算機控制及數據採集系統的硬體設計等內容。
  11. The double air regulator control riveting speed effectively

    氣路加裝雙向調節閥，有效控制鉚頭上下速度。
  12. Axis coaxial, and available fixes a position in the clamping apparatus

    氣路加裝雙向調節閥，有效控制鉚接速度。
  13. The double air regulator to control riveting speed effectively

    氣路加裝雙向調節閥，有效控制鉚接速度和回程速度。
  14. An engineer case is introduced, which is about " the reconstruction of high voltage fan ' s speed - adjusting by frequency conversion and the design of plc ( programmable logic controller ) control system in shui cheng iron and steel company ". in this project, an advanced controlling technology, based on the method in this paper, is used to realize the closed loop control of discharge header pressure of two coke ovens

    介紹「水鋼煤焦化公司鼓風機高壓變頻調速及系統plc控制改造」的工程概況，對煤氣鼓風機採用先進的變頻調速技術和計算機控制技術進行改造，實現對兩座焦爐集氣管壓力自動調節的閉環控制功能，既滿足了煤氣量的自動調節的要求，又避免了煤氣鼓風機出口閥門的節流調節，節能效果相當可觀。
  15. D. be adapted with two - way throttle valve which makes movement parts for easy adjusti

    採用雙向節流調速閥，使各運動部件調節更為方便。
  16. Used the metering - out control system in which the hydraulic cylinder was the executive element as research object in this thesis, the experimental research about the effect on the pressure p1, p2 of the hydraulic cylinder chambers when series - connecting throttle valve or governor valve on the return oil - line under the step load changing have made

    本文以單出桿液壓缸為執行元件的出口節流調速系統為研究對象，在其迴路上分別串接節流閥和調速閥，當負載發生階躍變化時，對液壓缸兩腔壓力p _ 1 、 p _ 2的影響進行了試驗研究。
  17. At the beginning of this article, we give the analysis about the principle of external condensation. we find out that the most important factor in the condensation is the temperature of the air in the system. and we point out the factors which can make influence in the external condensation, such as the temperature and the humidity of the environment, the temperature and the pressure of the supplying air, the load of the system, the area of passage of speed control valve, and so on. next, we give the mathematics model of the pneumatic system using the knowledge of aerodynamics and heat transfer theory. and using the finite difference method and the numerical analysis we can get the solutions of the model. we use c program to simulate the model

    本文首先對氣動系統外部結露的原理進行了分析，指出了氣動系統內部氣體溫度下降是氣動系統外部結露根本原因，提出了影響氣動外部結露的主要因素，包括環境溫度、環境濕度、供氣壓力、供氣溫度、氣缸負載和調速閥開度等。然後應用氣體動力學、氣體熱力學和傳熱學對氣動系統建立數學模型，用逆步進有限差分法和數值分析演算法對所建模型進行求解，利用c語言編製程序對氣動系統模型進行模擬，給出了氣管及氣缸內氣體的各個時刻的狀態參數。
  18. The air components are all takes the famous brand to use, the double regulator control the feeding speed and return speed effectively, the air - current added the aerosol device and it has the function of filter

    氣壓元件全部採用進口件，質量可靠，另外增加雙向調速閥，氣路加裝氣霧潤滑和氣體濾水功能，方便鉚接參數調整。
  19. Specification for torpedo speed regulating valve

    魚雷調速閥規范
  20. Hydraulic fluid power - compensated flow - control valve

    液壓調速閥
分享友人
分享到 Line

分享到臉書