負載傳感器 的英文怎麼說

中文拼音 [fùzǎizhuàngǎnqì]
負載傳感器 英文
load sensor
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  • 感 : Ⅰ動詞1 （覺得） feel; sense 2 （懷有謝意） be grateful; be obliged; appreciate 3 （感動） move; t...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 負載 : [電學] load
  1. Then a vsc controller using on - off valve and two potentiometers are designed for cushioning control system. it can realize the balanced, no shock, no reversing cushioning. experiments under different air pressure, load mass are carried out, and the results prove that the vsc controller can be used in pneumatic cushioning

    第五章首先介紹了變結構控制的原理和應用發展情況，然後針對本實驗系統設計了一個使用開關閥和端位位移傳感器的變結構控制方案，實現緩沖過程的平穩無沖擊和無回彈要求，並在不同氣源壓力、不同負載質量下分析了控制性能的變化，實驗結果證明緩沖控制採用變結構控制是可行的，並具有很強的魯棒性。
  2. The improvement system is made up of the pressure sensor, flow sensor, displacement sensor, electro - hydraulic proportional flow control valve, power amplifier, data gathering board and computer. the platform can carry out testing the hydraulic parameters, processing the tested data, saving the processed data and drawing, adjusting the pressure automatically

    改造后的測控系統主要由壓力傳感器、流量傳感器、位移傳感器、比例節流閥、功率放大器、數據採集卡和計算機組成。改造后的實驗臺具有自動採集實驗數據、自動處理實驗數據、自動保存實驗數據、自動調節液壓系統負載壓力等功能，大大提高了實驗臺的工作效率、測試精度和智能化水平。
  3. And then, the error matrixes of location and kinemics of the end point, and the on - line error compensation method are given based on robot ' s dynamics. finally based on puma robot, three simulation examples are given respectively ; the first is about the location error and on - line location error compensation, the second is about the kinetic error and on - line kinetic error compensation, the third is about location and kinetic errors causing by robot ' s dynamics and the on - line error compensations. the simulation results show that : a ) location error of the end point based on elastic deformation of the sensor will be about millimeter ' s degree under the permitting load, b ) the on - line error compensation methods given are available

    第三章首先概括了目前機器人連桿慣性參數識別的四種方法，總結這些方法的優、缺點；指出這些方法存在的問題是：或者需將機器人解體，不能在線進行參數識別，或者不能給出機器人連桿獨立的慣性參數值，只能獲得慣性參數的組合值，而這些方法的共同問題是：不能考慮機器人連桿的關節特性；本章提出了一種基於腕力傳感器的機器人末端連桿慣性參數在線識別方法，給出了該方法的理論計算和推導；研究提出了以腕力傳感器輸出為前提的、基於newton - euler動力學的機器人動力學正向、逆向遞推公式；針對機器人負載參數辨識必須在線、實時的特點提出了基於腕力傳感器的負載參數在線識別方法，給出了負載參數識別的步驟。
  4. Combined with researches on propagation characteristics, the micro - current sensor for on - line pd monitoring is developed and the effects of coil number, stray capacitance and loading resistance on pass - band and sensitivity are also studied

    同時，結合傳播特性，研究了局部放電在線監測寬帶微電流傳感器，並就線圈匝數、雜散電容和負載電阻等對傳感器通頻帶、靈敏度等性能參數的影響進行了分析。
  5. Loadfoot bowl head for best force transmission for force transducers with blind hole

    負載底座碗形頭，用於頂級的帶盲孔力傳感器的力傳遞
  6. 3069. 700 and 3096. 710 loadfoot bowl head for best force transmission for force transducers with blind hole

    負載底座碗形頭，用於頂級的帶盲孔力傳感器的力傳遞
  7. Loadfoot mounting flange and bowl head for best force transmission for force transducers with blind hole

    負載底座裝配法蘭和碗形頭，用於頂級帶盲孔力傳感器的力傳遞
  8. Vertically adjustable loadfoot bowl head for best force transmission for force transducers with blind hole

    垂直可調節負載底座碗形頭，用於頂級的帶盲孔力傳感器的力傳遞
  9. The simulated test of the mechatronics soft start equipment is made regarding the experimental platform of belt conveyor as load, the sensor design is had for selecting type, the testing datum are gatherd and analyzed, the rational curve of velocity in the starting and braking progress are gained, the best matching ratio of driving power for the double asynchronous moters is found

    以帶式輸送機實驗臺為負載進行了機械電子式軟起動裝置的模擬試驗，對傳感器進行了選型設計，對試驗數據進行了採集與分析，確定了合理的起、制動速度曲線，求出雙電機驅動功率的最佳配比。
  10. Strain - gauge load cell or force transducer, minimum load impedance 320r

    應變測壓元件或傳感器的最低負載阻抗為320r 。
  11. Recent years, the using of piezoelectric sensors becomes a focus in novel biosensors research. the basic principle is that the characters of its oscillation are highly responded with the changes of the surface mass adsorption, or the physic characters in the reaction system including density, viscosity, conductivity and so on. a piezoelectric biosensor with a nanogram sensitivity could be constructed through a reasonable biological processing and structure designing to the piezoelectric quartz crystal

    近年來，壓電傳感器檢測技術逐漸成為生物分析中的研究熱點，其基本原理是利用石英晶體振蕩特性對石英晶體表面質量負載（質量效應）和反應體系物理性狀如密度、粘度、電導率（非質量效應）等的改變具有高度敏感的特性，通過對石英晶體進行適當的生物學處理和結構設計，構建出具有具有ng級檢測能力的生物傳感器。
  12. It significantly outperforms an array of spatially displaced pressure hydrophones of comparable array - manifold size and computational load but may involve more complex hardware

    與聲壓傳感器組成的陣列相比，相當的陣列尺寸和計算負載的條件下，大大提高了估計性能。
  13. 3069. 700 and 3096. 710 loadfoot mounting flange and bowl head for best force transmission for force transducers with blind hole

    負載底座裝配法蘭和碗形頭，用於頂級帶盲孔力傳感器的力傳遞
  14. The force transducers with a nominal load of 5kn and an overload withstand capability of up to 10kn, are designed with dynamic fatigue strength for several million load alterations

    額定負載為5 kn ，超載負荷能力最大為10 kn ，具有動態疲勞強度設計的力傳感器要可以承受多達幾百萬次的負荷變化。
  15. The digital interface of tecsis pressure sensors ensures a perfect hook - up to the bus system of the load distribution system

    Tecsis壓力傳感器的數字化介面保證了與負載分佈系統的總線系統構成一個完美的連接。
  16. 3069. 700 and 3096. 710 vertically adjustable loadfoot bowl head for best force transmission for force transducers with blind hole

    垂直可調節負載底座碗形頭，用於頂級的帶盲孔力傳感器的力傳遞
  17. And then, a method of load - flow low - pressure measurement was proposed in the light of the hydraulic - resistance theory of servo valve. the validity of the method was proved by the experimental results. therefore, the measurement of the characteristic of load - flow and no - load flow can be realized by using this method

    然後根據電液伺服閥的液橋理論提出了一種負載流量低壓測量方法，在所開發的測試系統上，利用電液比例閥模擬流量測量裝置對所提出的方法進行了試驗驗證，實現了利用低壓流量計和壓力傳感器進行電液伺服閥負載流量特性和空載流量特性的測量。
  18. 3. at first, author summarizes the four methods of identification robot ' s inertial parameters at present in chapter 3, and points out advantages and disadvantages of the methods

    第四章是基於腕力傳感器的機器人慣性參數在線辨識方法的實驗研究，實驗在puma562機器人上進行，實驗時機器人末端連桿和負載為已知慣性參數的試件。
  19. Prototype experiments on an 40 - node linux cluster show the this scheduling schemes outperform the popular load balance approach by cutting the average response time, with only little trade - off in overall throughput. further experiment on larger number of sensors demonstrates the cluster server maintain the optimized performance under high intensity workload. in our next phase of work, is focus on the linux kernel

    隨后的大傳感器數量實驗和高強度主動型全分散式調度策略實驗證實了主動型全分散式調度策略演算法在高負載下優異的實時響應特性和穩定的系統產出率，表現出這種新演算法在支持大型集群體系，提高系統擴展性上的巨大潛力。
  20. The materials and technology used make these pressure sensors insensitive to chemically aggressive media and mechanical load

    壓力傳感器的材料和技術可以抵抗化學腐蝕介質和機械負載。
分享友人
分享到 Line

分享到臉書