負載變化 的英文怎麼說

中文拼音 [fùzǎibiànhuà]
負載變化 英文
load change
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 負載 : [電學] load
  1. According to the operation condition, it is shown that the protector presented in this paper can duly follow the motor ' s load fluctuation and capitally match with motor ' s tolerance overload characteristic, thus it is valuable to be actually used

    運行結果表明，本文所研製的單片機式熱保護電器能較好地動態跟蹤負載變化，其熱保護特性能較好地與電動機的允許過載特性相匹配，有一定的工程實用價值。
  2. The load is changed with many factors such as temperature, magnetic reluctivity, etc. and its parameters are difficult to measure. so the worst working situation is difficult to know, which is a serious problem when the starting issue is studied

    在研究逆變器的啟動問題時，由於負載變化大，參數很難準確的測量，無法得知可能出現最嚴重的工況，給研究帶來了很大的困難。
  3. Because of the temperature rising of ultrasonic motors, load changes, and vicinal surrounding changes and so on, the resonant frequency will shift, leading to working stability drop

    由於超聲波電機的溫升、負載變化及周圍環境變化等原因，使電機的諧振頻率發生漂移，這將影響超聲波電機運行的穩定性。
  4. The soft switching, phase - shifted pwm and bi - directional dc - dc converter hang together, depress circuit switching loss and noise effectively, which provide condition to increase switch frequency, efficiency and reduce size and weight for the converter ; at the same time, it is proved the converter can achieve zvs in larger load variation, and the converter has the virtue of structure compact, voltage and current stress small such as ordinary hard switch converter

    該變換器把軟開關技術和相移控制pwm技術以及雙向dc - dc變換器技術有機結合在一起，有效地降低了電路的開關損耗和開關噪聲，為變換器裝置提高開關頻率、效率以及降低尺寸及重量提供了良好的條件;同時，能拓寬零電壓開關的范圍，使變換器在較寬的負載變化范圍內都能實現軟開關。
  5. Great intermittent noise, wide variety of impendence along with the load and great attenuation of signals have restricted the further utilization of power line

    但是，電力線通信通道存在間歇性噪聲大、阻抗隨負載變化大、信號衰減大等缺點，嚴重製約了它的有效利用。
  6. Zero - voltage turn - on and zero - voltage turn - off in lagging arm and leading arm of soft - switching topology, working waveform of power transformer and process of rectifier and transition are presented in detail. the influence of resonant inductance of the power transformer, resonant capacitor and variation of load to the process of soft - switching are given

    主要對軟開關滯后橋臂和超前橋臂的零電壓開通、關斷過程，功率變壓器的工作波形及整流換流過程進行了詳細的模擬分析，並重點討論了逆變器的諧振電感、諧振電容以及負載變化對軟開關過程的影響。
  7. The possible factors including the deviation of temperature in length and breadth of rod, the changes of transfiguration resisting force under the changes of temperature, the adjustment of roll gap, the variation of rolling pressure, the changes of roller speed during dynamic adjusting press, the unmatched of seconds - flux under the dimension fluctuation of the coming sample and so on. the whole system was a closed loop which factors in it interacts each other

    可能的影響因素有:沿軋件縱橫向溫度變化、由溫度引起的軋件變形抗力變化、軋機輥縫值變化、負載變化、電機調節系統由不穩定向穩定過渡過程中軋輥轉速的變化（如咬鋼過程中的動態速降后的回復階段） 、來料尺寸波動造成秒流量不匹配等，整個模擬系統是各個因素相互影響關聯的一個閉環系統。
  8. The systems are composed of single - chip microcomputer and several kinds of interface circuits and control the voltage to run after the change of load

    該系統是由單片機和各種介面電路組成，控制電機的電壓跟蹤負載變化，達到節能的目的。
  9. This thesis also have constructed mathematic model based on the analytic method, which used the load as input and the pressure as output, meanwhile, it have made theoretic analysis of time response. the theoretic analysis was highly agreed with the experimental result

    在對出口節流調速系統液壓缸兩腔壓力隨負載變化的動態特性的理論分析時，用解析法建立了以負載為輸入，壓力為輸出的數學模型，進行時間響應分析，其理論分析結果與試驗結果相吻合。
  10. Through experimental research, the calculation formula that the pressure highly - adjusted capacity of two cylinder chambers varied with the change of step load and the formula about hydraulic elements main parameter ( rated pressure ) were both made, which had important valuation in selecting the main parameter about this hydraulic system

    通過試驗研究得出了出口節流調速系統中液壓缸兩腔壓力超調量隨負載變化的計算公式以及出口節流調速系統中液壓元件主參數（額定壓力）計算公式，有利於正確選擇系統的元件及主參數。
  11. The analysis and study on the dynamic efficiency of pmsm performing under the various loads. the influence of machine ' s parameters on dynamic efficiency and dynamic power factor is studied ; this has significant meaning for design of pmsm applied in the various load fields. the theoretical analysis and fem calculation fo air - gap magnetic field of pmsm is done

    在建立永磁同步電動機dq軸數學模型時，考慮了電機的鐵耗和雜散損耗，提高了模擬計算的精度，根據實測的負載變化情況，對永磁同步電動機的動態性能進行模擬，並研究分析了電機各參量對其動態平均效率和動態平均功率因數的影響，總結出變化規律。
  12. The formulas of three kinds of loaded ultrasonic transformers are presented ; then, the graphs of resonance frequency and the amplitude magnification coefficient, following the change of load, are charted by the programs of matlab

    得到了三類常用變幅桿頻率方程和放大系數的表達式；並通過matlab編程，分別繪制了三類變幅桿共振頻率及放大系數隨負載變化的曲線圖。
  13. The effects of the error of ct and vt, hysteresis and load variation to short - circuit reactances are discussed also. by using error analysis and simulation analysis, this paper discussed the feasibility in engineering

    論文分析了互感器誤差在幾種情況下對短路電抗測量結果的影響；通過變壓器建模，分析了磁滯特性和負載變化量大小對短路電抗測量結果的影響，驗證了該方法在工程應用上的可行性。
  14. By close study on the average temperature rise, temperature distribution, and tune constant of the class f resin dry type power transformer ' s high voltage and low voltage winding under self - cooling and wind - cooling mode, we find out the connection between the variation of the load and the items, mentioned above. the results of the experiments can be reference to both thermal design optimization of dry type power transformer and the revision of current standards. meanwhile, we develop the software, which can predict the overload ability of the dry type power transformer

    本文對f級樹脂澆注式乾式變壓器的高、低線圈的平均溫升，內部溫度分佈和時間常數在自冷和風冷，兩種冷卻方式下隨負載變化的規律進行了研究，得出了平均溫升、熱點溫升和時間常數隨負載變化的相互關系和有關計算用參數和公式，試驗結果可作為改進乾式電力變壓器的熱設計的依據和對現行標準進行修改的參考。
  15. Compared with phase - shift control, pwm plus phase - shift control can reduce the current stresses and rms currents of the converter. the loss of the converter can also decrease. lt is proved the converter can achieve zvs in larger load variation

    與常規相移控制方式相比， pwm加相移控制方式能減小變換器的電流應力，減小通態損耗，同時也能拓寬零電壓開關的范圍，使變換器在較寬的負載變化范圍內都能實現軟開關。
  16. The experiment result shows that conversion efficiency in ccm is improved by 2 percent compared with that in dcm, although the on - resistance of winding in ccm is more than that in dcm. the analysis of open - loop transfer function in both dcm and ccm shows that pull - push hfl inverter at ccm

    微分補償網路的推挽高頻鏈逆變電路在輸出從空載變化到額定阻性負載變化的過程中，逆變電路工作模式從dcm變化到ccm模式，實驗結果表明電路在這兩種模式下都能輸出穩定的正弦電壓，且具有較高的穩態精度。
  17. Hunting hunting is a phenomenon that can occur upon load changes in which the frequency or the voltage continues to rise above and fall below the desired value without reaching a steady - state value

    游車游車是一種在負載變化引起的頻率、電壓高於或低於期望值，無法達到穩定的現象。
  18. According to the results of the simulation and experiments, it is known that with the controller which is depended on the h algorithm the system is self - adaptive and has the robust character for the change of the model parameters. and the outside inferences and load variation can be retained effectively

    模擬和試驗結果表明，本文基於h _控制演算法設計的控制器可以使系統具有良好的跟蹤特性和對系統參數攝動的魯棒性，可以有效地抑制負載變化和外界干擾，滿足了系統的要求。
  19. The problem of noise is a chief block to restrict the popularity and developement of the plc because of the irregularity of power line network, the randomness of transmission distrance and load facility diversities

    由於低壓范圍內電力線網路的非規則性、傳輸距離的隨意性、以及電力線上負載變化的多樣性，使得干擾問題成為制約低壓電力線載波通信發展和普及的主要障礙。
  20. Repetitive control is used to reduce voltage distortion under abrupt load variation or nonlinear loads and attain good quality of the voltage waveform ; current loop is designed to quicken the dynamic response and strengthen the ability of the inverter control

    重復控制可以抑制逆變電源在負載變化嚴重（空載加到滿載）或者非線性負載條件下的輸出電壓畸變，保證輸出波形的質量；電流環用以改善輸出波形的動態響應特性，提高逆變控制的能力。
分享友人
分享到 Line

分享到臉書