起動曲柄 的英文怎麼說

中文拼音 [qǐdòngqūbǐng]
起動曲柄 英文
cranking lever
  • 起 : 起Ⅰ動詞1 （站起; 坐起） rise; get up; stand up 2 （取出; 取走） draw out; remove; extract; pull 3...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 柄 : Ⅰ名詞1 （器物的把兒） handle 2 （植物的花、葉或果實跟莖或枝連接部分） stem 3 （言行上被人抓住的材...
  • 起動 : start （a machine, etc. ）; switch on起動電動機 starting motor; 起動器 starter
  1. The crank reference pulse originates from a variable reluctant pickup which senses a projection on the engine's flywheel.

    曲柄參考點脈沖信號由一個變磁阻傳感器產生，它從發動機飛輪上的突起感受信號。
  2. This drilling adopts crank connecting link and walking beam percussion mechanism, which make the drilling possess two percussive functions, normal drilling takes connecting link impact as main mode, when encountering special situation and the connecting link impact can not drill, it can transform into hoisting impact, the stroke length can be modulated, it realizes automatic percussive drilling due to continuous operating of connecting link percussive mechanism, these can enhance drilling efficiency and relieve labor intensity ; it adopts pumping reverse circulation to drain slag, which not only resolves the drilling difficulty in special stratum such as pebble and gravel stratum and hard stratum, but also resolves the problem that the percussive drill ' s efficiency is low ; it adopts spur gear differential mechanism as double cylinders lazy tongs of main hoist, which not only ensures the balance state of drilling tool, but also reduces the mechanical design, and reduces the cost ; the bottom plate traveling motion of this drilling machine adopts walking type ; the drilling tower adopts hydraulic pressure uprising, and reduces the assistant operating time

    該鉆機採用曲柄連桿、游梁式沖擊機構，使鉆機具有兩種沖擊功能;正常鉆進以連桿沖擊為主，遇到特殊情況，用連桿沖擊不能鉆進時，可轉為卷揚沖擊，沖程可調，因連桿沖擊機構連續工作，所以實現了自動沖擊鉆進，可提高鉆進效率，減輕勞動強度;採用泵吸反循環的方式排渣，既能有效解決卵礫石地層、堅硬地層等特殊地層鉆進的困難，又很好地解決了沖擊鉆機效率低下的問題;採用直齒圓柱齒輪差速機構作為主卷揚的雙筒同步機構，既保證了鉆具處于平衡狀態，又大大簡化了該機構設計，降低了成本;該鉆機底盤行走移位採用步履式;鉆塔採用液壓起立，減少了輔助作業時間。
  3. It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great

    曲柄連桿機構在高速運轉過程中，有曲軸的轉動、連桿的擺動及活塞的往復運動，其運動狀態復雜，各個部件所產生的周期性不平衡慣性力大，是引起發動機振動的主要原因。
  4. The crank - set of motor is a special rotate machine, in which the inertia combined - force caused by running crank will tremble the whole automobile along with rack. therefore, it has practical meaning to locate the inertia combined - force and eliminating its influence on whole system, which can reduce the uncomfortable feeling of driver, also promote entire performance

    發動機曲柄連桿是一種特殊的旋轉機械，其工作時產生的慣性力的合力會使發動機工作時產生振動，這個振動傳遞到機架上，引起整車的振動，從而使駕駛者感到不適，同時對整車性能產生不利影響，因此，找出並消除這個慣性力的合力對于提高車輛的整體性能有著重要意義。
  5. This microstructure stimulates the piezoelectricity thin film rocking bar using the oscillating circuit to have the vibration, rocking bar impetus slide around translational motion, simultaneously tows the crank to have the rotary motion

    該微結構?用振蕩電?激發起壓電薄膜搖桿生成振動，搖桿帶動?塊前後直線移動，同時牽引曲柄生成旋轉運動。
  6. Based on above background, a elastic slider - crank mechanism, which is a typical engineering chaotic vibration system, and its dynamical response are selected and analyzed, in order to realize the combination of chaotic theory with engineering application and to serve latest theory as the guidance for structure design

    本文選取了彈性曲柄滑塊機構這一典型的工程混沌振動系統為研究對象，研究其動力學行為，以期將混沌振動理論研究與工程實用結合起來，使學科前沿的理論成果能對具體的彈性結構設計發揮指導作用。
  7. The massive walking - beam rose and fell above the deck ; at one end a piston - rod worked up and down ; and at the other was a connecting - rod which, in changing the rectilinear motion to a circular one, was directly connected with the shaft of the paddles

    甲板上露出一根很長的蒸汽機杠桿，兩頭一高一低地不停活動，這根杠桿的一端聯接著活塞柄，另一頭聯著輪機上的曲軸，這樣就把杠桿的直線推動力轉變為直接推動輪機的動力，從而使輪軸不停地旋轉起來。
分享友人
分享到 Line

分享到臉書