超細研磨機 的英文怎麼說
中文拼音 [chāoxìyánmójī]
超細研磨機
英文
super grinder- 超 : Ⅰ動詞1 (越過; 高出) exceed; surpass; overtake 2 (在某個范圍以外; 不受限制) transcend; go beyo...
- 細 : 形容詞1 (條狀物橫剖面小) thin; slender 2 (顆粒小) in small particles; fine 3 (音量小) thin ...
- 研 : 研同 「硯」
- 磨 : 磨動詞1 (摩擦) rub; wear 2 (研磨) grind; mull; polish 3 (折磨) grind down; wear down [out]:...
- 機 : machineengine
- 研磨 : 1. (用工具研成粉末) grind; pestle2. (用磨料摩擦器物使變得光潔) abrade; polish
-
The principle products include project of complete glazing line, accessory machineries for press / dryer / kiln, deep - processing machine ( e. g. polishing machine for glazed ceramic, newest fully automatic gashing machine, high speed miller machine ), silicon cylinder engraving service and ceramic designs offer etc, which of market share is ahead of those working for similar industries and sold out to south - east asia, mid - east, south - america and africa
公司主要產品包括:印花機、釉線及釉線上配套產品、全自動仿古磚拋釉機、新型劃磚(界磚)機、高速超細研磨機、輥筒機輥筒激光雕刻及圖案設計等,其產品市場佔有率均列同行之首,並銷往東南亞、中東、南美洲、非洲等地。The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement
研究結果表明,增大砂輪軸向進給速度和減小工件轉速,採用粗粒度砂輪有利於提高磨削矽片的材料去除率,砂輪軸向進給速度對材料去除率的影響最為顯著;適當增大砂輪轉速,減小砂輪軸向進給速度,採用細粒度砂輪可以減小磨削表面粗糙度;在其它條件一定的情況下,砂輪速度超過一定值會導致材料去除率減小,主軸電機電流急劇增大,表面粗糙度變差;採用比# 2000粒度更細的砂輪磨削時,材料去除率減小,矽片表面粗糙度沒有明顯改善。Firstly, the mechanism of the preparation of superfine quartz powder with ball mill is studied in this article, based on nature of quartz material, griffith ' s strength theory and the crush theory of planetary ball mill. the problem of granulation during the process of the preparation of superfine quartz powder is studied minutely. and proposed increasing dispersant and disperser medium to restrain granulation, and dispersing use ultrasonic after milled
首先,本文結合石英材料的基本物性,以格里菲斯強度理論和行星式球磨機的粉碎原理為基礎,研究了球磨法制備超細石英粉體的機理,同時對粉石英制備過程中的團聚問題及其控製作了細致的研究,提出粉磨過程中增加分散劑和分散介質來抑制團聚,粉磨后採用超聲法進行分散,並確定了最佳分散劑、分散介質的用量和最佳超聲分散時間。Superfine grinding and surface modification of gcc by vibratory mill
用振動研磨機對重鈣進行超細及表面改性Gcc superfine grinding and surface modification by vibratory grinding mill
用振動研磨機對重鈣進行超細及表面改性This paper presents the test result comparing a vibrating grinding mill with a ball grinding mill in milling efficiency, power consumption and medium wear, analyzes major process parameters of vibrating grinding mill and gives reasonable suggestion for selecting these parameters
摘要通過實驗測試對振動磨機與球磨機的研磨效率、能量消耗、介質磨損進行了分析比較,證明了振動磨機在細磨,尤其超細磨時優勢凸顯;同時對振動磨機的主要工藝參數進行了對比分析,提出了在振動磨機設計時合理確定這些參數的建議。The planet type ball mill is the laboratory, produce in batches by grinding, mixing the equipment high - efficient and ultraly and thinly small
行星式研磨機是實驗室、小批量生產用高效超細研磨、混合設備。The tribological characteristics of ultrafine ws2 powders added in engine oil have been investigated by four - ball machine test, and compared with chloroparaffins ( t302 ) and molybdenum disulphide ( mos2 ), and meanwhile we have analyzed the tribochemical species of the worn surface by means of x - ray photoelectron spectroscope ( xps ), to research the lubricating mechanism of ws2
摘要採用四球摩擦實驗機對二硫化鎢超細粉末在發動機油中的摩擦學性能進行了研究,並與添加劑氯化石蠟和二硫化鉬進行了比較,同時用x射線光電子能譜儀對磨痕表面元素進行分析,以探討二硫化鎢的潤滑機理。分享友人