車架承梁 的英文怎麼說
中文拼音 [jūjiàchéngliáng]
車架承梁
英文
body bolster- 車 : 車名詞1. (中國象棋棋子的一種) chariot, one of the pieces in chinese chess2. (國際象棋棋子的一種) castle; rook
- 架 : Ⅰ名詞1 (用來放置東西或支撐物體等的東西; 架子) frame; rack; shelf; stand 2 (毆打; 爭吵) fight;...
- 承 : Ⅰ動詞1 (托著; 接著) bear; hold; carry 2 (承擔) undertake; contract (to do a job) 3 (客套話...
- 梁 : 名詞1 (屋架中架在柱子上的長木) beam 2 (通常也指檁) purlin 3 (橋) bridge4 (物體中間條狀隆起...
- 車架 : frame (of a car, bicycle, etc. ); carriage; carframe
-
For reinforcement concrete corbel with the shear span to depth ratio ( a / ho ) less than 1, has its performance of mechanics that is close to cantilever deep beams, it is an important kind of components in architectural structure which sustains roof trusses, brackets, tray " beams, frame " beams, wall " beams and crane " beams
剪跨比a h _ 0 1的短鋼筋混凝土牛腿,其受力性能接近於懸臂深梁,在建築結構中是支承屋架、屋面梁、托架、托架梁、框架梁、墻梁和吊車梁等的重要構件。Based on practical project of inspecting, appraising and reinforcing a main heavy factory building, especially its steel crane girder system, of the second steel mill belonging to taiyuan steel & iron corporation, whose technology renovation leads to increase tonnage of many heavy cranes and vertical load of frame - bent structure, first the structure and its members were investigated, inspected, calculated and analyzed, and their reliability was appraised respectively and the strengthening projects or the measures to remedy were given. then, in accordance with the requirement to strengthen the girders under non - stop production, the feasibility of strengthening the crane girders by adding steel diagonal braces underneath the existing girders has been studied by inspecting and evaluating the strengthening effect of the crane girders and comparing with other reinforcing scheme
本文結合太鋼(集團)有限公司第二煉鋼廠主廠房由於生產工藝改造要求,加大多臺重型吊車噸位及bc跨( 1 ) ( 8 )軸線框排架各層豎向(設備)荷載后,對廠房結構,尤其鋼吊車梁系統進行檢測鑒定與加固設計的實際工程,首先對廠房結構進行了現場調研、技術檢查、測試以及內力和承載能力的計算與分析(考慮抗震) ,並根據檢測、計算與分析結果,對廠房結構、構件的可靠性進行了評定,並綜合提出鑒定結論和加固處理建議。Test methods of static load for truck frames and truck bolsters of railway rolling stock
鐵路車輛用貨車車架和轉向架承梁靜荷載的試驗方法Then calculate the member individually, including the calculation of load - behavior capacity, the calculation of high strong bolt with the method of connection with beam, the design method of stiffening rib, etc. the text educed the above - mentioned formula theoretically. 5. linking with windmill flat engineering example in the third youth flat engineering of yi zhuang development area, beijing, it and steel frame constitute the steel frame ? steel shear wall with slit system respectively are analyzed the whole structure by ansys and satwe
既利用剛度等效的原則,把其轉換為工程計算軟體可以計算的支撐體系,然後對構件進行單獨計算,包括承載力的計算、和梁接合方法? ?高強螺栓的計算、加強肋的設計方法等內容; 5 、帶縫鋼板剪力墻與鋼框架形成鋼框架? ?帶縫鋼板剪力墻結構體系,結合北京亦莊經濟開發區青年公寓三期工程中的風車公寓工程實例,分別採用ansys和satwe進行了結構整體分析,兩者的計算結果相吻合。On the basis of detailed comparison and analysis, the paper proposed ways of using the k2 bogie and hdsa light - duty solid wheel, getting through the partition wall, canceling the longitudinal sill of the roof and decreasing the thickness of the board where the value of stress is low, using high intensity steel, increasing section dimensions of center sill and side sill, to improve the whole carrying capacity
本文在比較分析的基礎上,提出了裝轉k2轉向架,採用hdsa輕型碾鋼輪,打通隔墻,取消車頂縱向梁,在應力小的部位減薄壁厚的減重對策;採用高強度耐候鋼,加大中梁、側梁的截面尺寸等措施,提高車輛的承載能力。According to the bearing load institute of mainly bearing component, the basic form of bridge can be classified into beam bridge, arch bridge, rigid frame bridge, suspension bridge and assembly system bridge etc. also according to the location of trip lane, it can be classified into top travel bridge, middle travel bridge and lower travel bridge
橋梁的基本形式按橋梁主要承重構件的受力情況可分為:梁橋、拱橋、剛架橋、懸索橋、組合體系橋等;按行車道的位置又可分為上承式橋、中承式橋和下承式橋。分享友人