軋制時間 的英文怎麼說

中文拼音 [yàzhìshíjiān]
軋制時間 英文
pass time
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. Abstract : by analyzing theae factors which influence the reduction process and ferrous powder ' s quality, reduction temperature, reduction time, scale thickness and additive quantity are chosen to discuss their effect on the chemical composition and the crashed property of sponge iron

    文摘:分析了馬鋼軋鋼鐵鱗的原料狀況，選取還原溫度、還原時間、料層厚度和添加劑等工藝因數來研究它們對海綿鐵化學成分和破碎性能的影響規律，為海綿鐵的工業生產提出合理的工藝制度。
  2. This method can decrease the gap setting time for which the oil column of hydraulic cylinder is not retracted and there is no minute adjustment of oil column for the first several passes

    採用該方法，軋制過程液壓缸油柱不用回縮，而且前面道次液壓不進行微調，從而節省了輥縫設定時間。
  3. The suspect told police he was riding his bicycle when he lost control and rolled down an embankment and onto railroad tracks just as a train was passing by, losing a thumb on one hand and an index finger and a pinky on the other

    這名犯罪嫌疑人告訴警方，事故發生在2003年11月，當時他正在鐵道路基上騎自行車，突然間失去控制摔下路基，滾到了鐵道上。這時恰巧駛來一列火車，車輪軋過了他的雙手。
  4. And relying on this, our laboratory proposes a new cladding method. by means of large dynamic explicit fem code ansys / ls - dyna, the numerical simulation was carried out in bimetal forming process. during the simulation of the forming process, the large deformation of the strip should be considered, as well as geometrical and material nonlinear, the contact between the roller and the strip, the contact between two metal sheets and the load. as for these problems, we can use node to surface contact and relative parameters, biso model is introduced, the load is applied as array

    本文採用ansys / ls - dyna計算程序為分析工具，對鋸齒形雙金屬復合板成型過程進行計算機數值模擬，在對軋制過程模擬時，針對軋件變形的幾何非線性和材料非線性特點、軋輥與軋件間的接觸、軋件間的接觸以及模型的加載等問題，給出了在ansys / ls - dyna中相應的解決方法：應用nodetosurface接觸方式，設定相應參數，選用雙線性等向硬化模型，載荷作為array施加在剛體質心。
  5. After long - term application on hot wide strip mills, varying contact rolling technology was proved to be effective in strip profile and flatness improvement roll consumption reduction and increase of rolled product length of rolling cycle

    通過在寬帶鋼熱連軋機上的長時間應用證明：變接觸軋制技術可以顯著改善軋后帶鋼的板形質量、降低軋輥消耗和增加軋制單位公里數。
  6. After the technique reform in 2003, the oracle database system replaced the file system, each data for the process system is saved in the oracle database system, and the oracle net 8 is used for the communication between the process servers. how to design a good database system in process system, and how to tune the oracle system become a important problem for pangan hot strip mill after technique reform. this paper introduce the oracle database application system in pangang hot strip mill process system for architecture 、 designing principle and ways

    熱連軋生產過程是一個快速過程，對過程式控制制系統的響應時間有很高的要求，通常在100至500毫秒級，過程式控制制系統本身的計算負荷又很重，由於oracle數據庫不是一個實時數據庫，如何設計一個適應熱連軋過程式控制制的oracle數據庫應用系統，以及如何優化oracle數據庫系統，使其穩定高效的運行，保證熱軋生產的順利進行，是攀鋼熱軋板廠過程式控制制系統改造后急需解決的一個課題。
  7. The results indicate that the time of press influences sawtooth distortion greatly, but infects sawtooth less. root of the sawtooth made by the method of static simulating rolling have no changes hardly, and from the upper distance the changes became, then on the top the sawtooth curves to the opposite direction

    結果表明：壓制時間對齒形的變形影響較大，對齒型的影響很小；模擬軋輥壓制的鋸齒，根部一段幾乎沒有變化，是從一段距離開始變形，然後在頂端向相反的方向彎曲；壓製成型后，鋁板厚度的變化很小。
分享友人
分享到 Line

分享到臉書